Book a professional blind repair service in South Brisbane

Replace cords on 3 sets of vertical blinds; 1 set - 1200mm 1 set - 1800mm 1 set - 3600mm

Hi, Need old blinds removed and a new blind installed. It’s 120x~150cm window. Replacement blind available, however will need to bring own tools. Old blinds are some sort of Venetian blind. New blind is a roller blind ‘Windowshade Hudson Blockout Roller’ Thank you!

Looking for someone to fix our roller blind which is slipping. It’s a double blind but only left side is affected.

Remove existing blinds and install new roller blinds

Remove existing blinds and install new roller blinds

Remove existing blinds and instal new roller blinds - total 5

Remove existing roller blinds and fix new blinds

Need very basic blackout white roller blinds in our sunroom. Rough measurements below -1 blind x 130w x120h  -3 blinds x 175w x120h 

Hanging blind on concrete wall

I want to replace the old blinds in my house with new ones

Install wooden blind in window over kitchen sink, and install curtain rod and curtains for S-Fold curtains over sliding door. Will need to trim track as slightly too long. Also put round mirror on wall. Will need to remove old blind/curtain.

Replace spliting wooden archatrive 2m framing door, and the. Reinstall vertical blinds

Instal 5 minute blind sheer curtains on one wall in living area. Curtains still in box with all required fixtures and fittings.

One of the louvres on my plantation shutter has come out of the frame. The shutters are quite old, so could you also check whether any other parts need to be repaired or replaced?

I require 2 roller blinds to be installed in my bathroom. I need the brackets to be moved in a fraction so need some extra holes to be drilled.

Wooden blind is stuck in closed position. The cord is jammed and unable to open or close the slats

I need someone urgently to cut down 4 x Stratco Ambient outdoor blind cassette/headboxes / blind components. Installation is already arranged. This task is for the cutting only. The blinds have been supplied slightly too large / too tight for the reveal openings. Stratco has advised that the manufacturer can speak directly with the person doing the cut to guide the process if required. Approximate cuts required: - Blind 1 / left side: received cassette/headbox 2986 mm. Requested adjusted length 2976 mm. Approx. 10 mm cut. - Blind 2 / front left: received cassette/headbox 4005 mm. Requested adjusted length 3996 mm. Approx. 9 mm cut. - Blind 3 / front right: received cassette/headbox 2949 mm. Requested adjusted length 2941 mm. Approx. 8 mm cut. - Blind 4 / right side: received cassette/headbox 2989 mm. Requested adjusted length 2979 mm. Approx. 10 mm cut. The cuts need to be accurate and clean. Please only apply if you have the right tools and experience cutting aluminium or similar blind/awning components. Important: - Final measurements must be checked before cutting. - No cutting should occur until the final cut measurements are confirmed. - Stratco/the manufacturer can speak with you before cutting if needed. - I can provide photos and the measurement table. - I can potentially bring the blinds to your workshop if that makes the job easier. - Job is urgent. Please include in your offer whether you have experience cutting aluminium cassette/headbox, awning, or blind components.

I need an experienced blinds installer / handyman to cut down and install 4 x Stratco Ambient outdoor blinds. The blinds have been supplied slightly too large / too tight for the reveal openings. Stratco has advised that the manufacturer can speak directly with the installer to guide the cutting process if required. Scope: - Attend site and inspect the 4 blinds and reveal openings - Confirm all measurements before cutting - Speak with Stratco / manufacturer if required - Cut / adjust the cassette/headbox/blind components as needed - Install the blinds within the reveal openings - Ensure the blinds operate properly after installation Approximate cut dimensions: - Blind 1 / left side: received cassette/headbox 2986 mm. Requested adjusted length 2976 mm. Approx. 10 mm cut. - Blind 2 / front left: received cassette/headbox 4005 mm. Requested adjusted length 3996 mm. Approx. 9 mm cut. - Blind 3 / front right: received cassette/headbox 2949 mm. Requested adjusted length 2941 mm. Approx. 8 mm cut. - Blind 4 / right side: received cassette/headbox 2989 mm. Requested adjusted length 2979 mm. Approx. 10 mm cut. For context, the received cassette/headbox lengths appear to be between 2 mm and 8 mm larger than the narrowest submitted opening measurements and do not appear to include a separate fitting tolerance / deduction for reveal installation. Important: The above measurements are provided to explain the job only. The successful installer must take their own check measurements on site before cutting. No cutting should occur until the final cut measurements are confirmed and, if required, discussed with Stratco / the manufacturer. Please only apply if you have experience with outdoor blinds, roller blinds, awnings or similar, and are comfortable accurately cutting aluminium cassette/headbox components.

Hi Everyone, Having dramas with my vertical bedroom blinds: the control cord/runner has disconnected and the controls no longer move the blinds. The slats can still be moved manually. Need the track/cord mechanism repaired, not full blind replacement unless necessary.

Hi, as seen in the photos, the wooden blinds in my spare room have fallen off the window. The top window frame has fallen off with it. I’m hoping that someone can come over and fix it. Thanks