Find a sockets and switches installation professional in West Melbourne

I tried to replace/fix my light switches and I broke them. 4 switches that turn on 1 light only 2 of them work now. And my garage lights don't work anymore.

Looking for a fully licensed, insured A-Grade electrician to complete a residential final fit-out. The rough-in phase will be fully completed before this task begins. All cables will be sitting ready at the plaster cut-outs with standard mounting brackets fully installed. I will supply 100% of the visible faceplates, mechanisms, and smart modules. The primary wall gear is brand-new Hager Finesse in Matt White. Scope of Work: Install, terminate, and test the following hardware items. (Base quantities listed below; final counts may vary slightly by 1-3 items on the day). Powerpoints: 44 x Double 10A GPOs (WBQP2S-MW) Pre-Assembled Push Button Switches: 20 x 1-Gang | 4 x 2-Gang | 3 x 3-Gang | 5 x 4-Gang | 1 x 5-Gang | 1 x 6-Gang (Note: All 34 plates will be handed to you fully pre-assembled by me with their internal wire-tail LED modules snapped into place. You only need to wire the tails into standard Locator Mode—so the LED stays ON when the switch is OFF). Cooker Isolation Switch: 1 x Hager 1 Gang Horizontal Rocker Switch (WBQCKSH1-MW). Smart Modules: 4 x Shelly Smart Relay Modules to be wired directly behind 4 designated wall plates. Active, Load, and Neutral connections will be roughed-in and ready at these 4 boxes. Data & TV Outlets: 10 x 1-Gang Plates containing a mix of 8x Cat6 Data Mechs and 2x F-Type TV Mechs (All mechanisms pre-installed into the plates by me). Requirements: - Valid A-Grade Electrical License and Public Liability Insurance. - Supply standard trade consumables for termination (wire connectors, tape, etc.). - Test all circuits and issue a compliance certificate / Certificate of Electrical Safety (COES) at handover.

Change power plugs and split switches for lights

Looking for a certified electrician to do the following. At this point looking for a quote to see if it meets my budget. x7 power sockets x2 pendant lights (to replace existing oyster lights in kitchen) x11 down lights (replacing oyster lights) x1 wall sconce in bathroom.

Power sockets in the garage area installed

Heated light installation

Need to fix my switches on the exhaust fan in the kitchen. Please see the pictures.

Relocate three light switches to nearby wall.

Need qualified sparky with insurance coverage to Install these 3 lights on ceiling at various ceiling locations. Single story house. 1*downlight - need material supply( as marked on the ceiling)- use existing switch. 2*spot lights with shared switch - light and switch bought already - new switch; 2*. PowerPoints? You supply material.

Remove and replace some of the lights switches, around 8 of them. I will provided the replacement

I have had the wiring completed in bathrooms and kitchen ready for renovation aside from 2 plugs in the ensuite , so I need them connected. The wiring and wires … and sockets are all here ready to connect.

Apologies to people who put a price on the original task. I opened Airtasker to pick someone and found the task had been cancelled by Airtasker as it was there for about a month.i am looking to get this done within the next week. I am looking for someone to change over some existing power points, light switches, install 1 new power point and fit off some smoke detectors. I will supply all materials so you only need to quote for labour. In total it is Change over 14 power points Install 1 x new power point change over 5 x light switches Install 3 smoke detectors and breaker to existing cabling. Connect 1 x LED Mirror and install switch for it. Change over 1 x Light fitting Powerpoints Change over Change over 14 power points in existing locations. This is just remove the old powerpoint and put the new one on. I will supply the specific powerpoint Install 1 new power point. This is in the bathroom. There is currently a powerpoint higher on the wall in the LED Mirror Cabinet. The power point to be installed is directly below this. Distance is 1m. I put in a draw wire when we had the plaster off. Light switches Change over light switch locations. 2 x single 2 x double 1 x 4 switches LED Mirror The mirror is already hung on the wall. Will need a switch installed next to current powerpoint. Smoke Detectors new cabling was installed for smoke detectors which I have a certificate for. Needs smoke detectors fitted off and a breaker installed in switchboard. Light Fitting Change over 1 light fitting. A certificate is a must have. Please only bid if you are a registered electrician. Money will not be released until the certificate is provided as I have had to chase people for months in the past.

One house has 4 TVs mounted but needing cables to not be showing. Another house 10mins away needing light switches on walls to be fixed.

The new DC 102cm fans with lights are to replace existing fans with lights that are in good working order. The new 62mm toggle switches are to replace existing toggle switches which have broken toggles.

Getting front and side doors replaced, and need our light switches moved to a new location in the house.

Install 6 single power sockets. Power sockets will be provided by me.

I need 3x power switches In laundry, room, pantry

Hi I'm looking for a registered electrician to fix a couple of electrical sockets. Based in West Footscray

Install 5 set of double power sockets, 1 set of triple power sockets on existing internal garage walls. 1- Supply and install 5 sets of double power sockets, 1 set of triple power sockets. Surface-mounted on existing internal garage walls, locations to be confirmed on site with owner. 2- Power sockets are to comply to Australian standard. Intended for home study use like laptops, study lights, computer monitor, printer). 3- Check if existing power circuit already has RCD protection at the switchboard or not. 4- Small garage size 5.5m x 2.85m. Socket are internal only and will garage is part of home, it is not exposed to weather. So using surface-mounting fittings is OK. 5- Test, label, and certify all new outlets with certificate. 6- If answer to 3 is "no", then provide optional quote: Ensure the circuit supplying the new outlets is protected by an RCD .

Our apartment has a balcony and the electrical power point has stopped working. We also need to re-affix a lose one and install a USB compatible power point in the kitchen.