Find a cladding professional in South Brisbane

I am looking for someone to do wall cladding. Approximately 13m² area materials will be provided

External weatherboard cladding painted - Due date: Flexible

Looking for the carpenters to finish external cladding. Hourly rate can be applied - Due date: Flexible

Hello, I need metal house cladding removed from one side of the upper level of my house and disposed of in preparation for painting. Roughly, half of one side has been done already, the remaining half needs to be done (24m2) Each piece of cladding is approximately 0.2m x 2-3m long. Cladding is joined on each end by 2 rivets and attached to chamferboard by metal clipping channel (along entire length of cladding). The first half was completed in approximately 3 hours, it was accessed by removing the timber fence and using painter’s trestles Awnings are attached by several batten screws that go through the metal cladding into the timber chamferboard underneath. The process could be, but is not limited to: - Loosen awnings or remove awning entirely (total 3 awnings) as necessary to access cladding underneath. -Drill out rivets on the ends of cladding where they are joined (see picture) -Unclip cladding and load into skip or vehicle for disposal -Where cladding is difficult to remove, it can be cut using angle grinder cutting blade (is easy and takes approximately 30 seconds per cut) -Once cladding is removed, remove clipping channels which are attached by clouts -Reattach awnings if necessary -Leave clean and tidy Height access equipment e.g. trestles to be provided by service provider or negotiated separately. Access is good however it’s not possible to get closer than 70cm to the house due to the neighbours ground level being approximately (1.4m) higher than mine. Total height to eaves approx. 5 m Whilst a relatively easy task, it would be best done by 2 people as the cladding can be awkward especially if at height. I can provide council dump vouchers. Please only apply if you have read this description completely, are physically fit, safety conscious and have similar experience. - Due date: Needs to be done on Sunday, 19 June 2022

Carport build. Steel frame with timber trusses and timber cladding. I’m an owner builder with council approved plans. It required two steel post out the front with beams back into the steel house frame.

I’m renovating a home. The external walls have a slight bow which needs to be packed to make square. The job requires; packing, supply and install of the colorbond sheets to external walls. The property has good access, off street parking. - Due date: Before Thursday, 24 March 2022

Painting windows and exterior cladding. 2 coats of oil based primer/sealer and 2 coats of colour. All paint suppled. Will need scaffolding, photos showing job attached. Come and quote. - Due date: Flexible

I have a granny flat which needs timber cladding installed to one exterior wall as well as soffits installed between the roof and the wall. I have the timber and the soffits, just not the time or skills. Granny flat has sarking plus blue board installed. Cladding is to go over the top of that and it is a steel frame structure.

Need a carpenter gang to do a cladding job for is. If you are interested please contact us.

Need to fix the wall cladding as it is damaged by a truck.

Finish the last 7 pieces of merbau cladding on back deck. All have to be cut on angles to fit Timber and screws supplied!

House was recently repainted but I have 3-4 rotted lengths of cladding i need cut out and replaced. 1 at about 2m and 2 at about 1.5m. I have lengths of cladding to replace the old ones with correct profile. Just need a builder to replace. Probobaly 2.5m off ground and I have ladder that I can set up to reach. Just need suitable nails or screws. Third row up from down pipe on photo 2 and then 2 lengths from first photo (about 4th and 8th row up).

Locate at Upper Mt Gravatt approx.150 m^2

New house needs cladding around bottom. Cladding can be attached to house stumps which are 1200mm high on east side and 900mm high on west side. Approximately 70m length in total. Thought of either timber or colour bond corrugated sheets would work.

Looking to get two pieces of vinyl cladding replaced. I’ve got no idea where you get this stuff. 1) first piece is a 1200mm long piece of dual cladding (~255mm total height for full dual piece) 2) second piece is a 1500mm long piece of flashing Both pieces are at ground level.

Looking for experienced tiler to tile outdoor bbq front and side with cladding tiles. All materials will be provided. Bbq is 2400mm x 700mm front and 2 x sides 700mm x 700mm. Roughly 5m2 of tiling. I’m flexible with when the job can be done.

Two storey home needs rendering/cladding for ground floor only post building construction handover. House size - 283sqm.

Aluminum wall cladding need to be replacement. The top 60% can be reused after being taken off. The 40% new matched cladding will be supplied by me.

Insulation touch up (needs spray adhesive to stay put) Screw And cut VJ BOARD accordingly A few cut outs required 6x small lights 2x roof vents Couple of 12 volt plugs to pull through Will help holding sheets up Need impact driver, circular saw, jig saw And a few different size circular drill bit

Ready to install, tongue and groove material requiring liquid nail and secret nails to fix on to existing gyp-board wall. Total work is around 55 sq meter of which 43 sq meter on to stairwell area ( height 6meters). Remaining behind TV as a feature wall, and bulkhead area in the kitchen. Installer has to to bring in all fixing material. Timber panels photos attached and so as the stairwell area.