Find an experienced driveway repair contractor in Sydney

Replace driveway gates and inserts of existing front fence

There is a small dead rat in my driveway. It was probably poisoned and dead already (flies are over it) and I unknowingly reversed my car on it (guts are spilled out).

Supply & install metal or pvc, “monument” colour fence and driveway gate. Short fence on top of brick fence. Open / close driveway gate.

Surface: The driveway is a mix of new concrete and older concrete (see attached photo). Want the area before the gate to look uniform, so cleaning and painting them all the same colour. Preparation: High-pressure wash and clean the entire area to remove dirt and prep for sealing. Sealing: Apply a high-quality concrete sealer in Colorbond Monument (dark grey/charcoal) to cover the area described.

I want to tile the driveway of my house to look the same as the pathway, Glazed terracotta tiles I think about 200x200 not sure. It’s probably about 15m long x 3 meters wide. (Would need to be measured). Quote supply and lay.

Sliding gate is sticking on pavers - need about 1 cm trimmed off tiles along length of gate

Note: This job can be completed on weekends or after hours. Need a concreter to patch some broken/cracked concrete around a sliding gate track and stormwater grate at the front of a commercial property (see photos). This is a small repair/patch job, not a full new driveway. Scope of works: • Inspect site and confirm repair area • Saw-cut around damaged sections of concrete along the gate track and near the drain • Break out and remove loose / drummy concrete • Prepare and compact base as needed • Supply & place high-strength concrete • Finish surface to match the existing level and falls for drainage

Painting decoration company

Looking to seal a new concrete driveway that was poured 28 days ago. It's about 14sqm, just a small front area. Any type of clear/matte seal would be ideal (if good quality seal - happy to listen to advice). Not fussed about painting it a certain colour, just want it protected.

The front wheel on our sliding driveway gate has fallen off. It seems like the screw thread has worn out due to friction over the years. Need a handyman to refasten/reinstall - may require installing a larger rivet nut (original hole fit an M12 bolt) and then rescrewing.

2.5 M2 of colour concrete

Plain concrete to Driveway, Council Crossover, Path, Layback Gutter • Concrete at 32mpa in strength and at 100mm thick to driveway, 130mm thick to crossover and 150mm thick to layback gutter. • SL82 Steel Mesh. • 50/65 Bar Chairs. • Expansion Joints. • N12 Dowels/Trimmer bars. • Excavation Works:- o Excavator / Bogey hire o Disposal of clean concrete & spoil o Road base – compacted • Controlled saw cuts. • Concrete pump hire. • Labour to excavate, prepare formwork/steelwork and to place and finish concrete at the above job address.

Need a few area to fill the cracks and resurface colour or stencil

I need my front yard levelled (sloped) and approximately 200mm of soil/grass excavated from an area 8m long x 2.5m wide to allow for preparation of road base for a driveway. The Tasker needs to provide all tools required (including mini excavator) and manage the disposal of the excavated soil as part off the job. There is easy access for a small excavator directly from the road via dropped kerb.

Wobbly tiles on the driveway needing to be fixed

Mount mirror on power pole to enable vision of road and footpath traffic when reversing from drive way. Mirror comes w bracket to fasten . Pole is wooden.

I think the door is rotten. If a steel one can be made will be better

To bolt to a concrete wall a 10 KMH sign approx 8M from ground, To spray paint in yellow paint on the entry of the concrete driveway and through out the complex, where the concrete are different levels. I have the yellow spray paint, the sign, the masking tape. You will a need a ladder and approx 1-2 hours. I estimate there are 6 levels which will need spray painting

Following cable installation across an internal driveway, the gap needs to be filled with quality quickset cement, and finished neatly to match the adjacent concrete. Width of gap approx 100mm, depth approx 100mm. Driveway approx 1.8m.

I would like a pair of colourbond gates brown in colour to replace the existing gates. The first pic shows what is currently there and the second pic is an idea of how I would like it to look. I believe it is possible to reuse the current steel frame to hinge the doors on Gates to have a lock fitted Dimensions are approx 1.8m high and width 2.72m