Find a professional pergola installation expert in VIC

Looking for someone to help with a simple decking and pergola job at our place. We’re looking at: * Approx. 5m x 7m composite deck (around 35m²) * Deck will be around 10-15cm high * Roughly half of the area is existing concrete and half is soil * No stairs needed * Simple covered pergola, approx. 2.6m x 7m * The concrete section is already under the existing house roof * The new pergola would extend over the deck area, with around 40–50cm clearance from the neighbour’s fence Nothing too fancy — just a simple, neat and practical setup. Happy for you to come and have a look and provide a quote. Looking for someone experienced with decking and pergolas and reasonably priced.

Painting of pergola - Have paint already.

Seeking an experienced carpenter or pergola installer to supply and install a minimalist timber pergola in a courtyard. The structure uses matching 90 mm posts and beams, with 240 mm beam depth for stiffness and a clean architectural profile. All connections must be concealed or minimalistic to achieve a seamless visual finish. Structure Requirements • Posts: 90×90 mm H4 treated pine • Beams: 90×240 mm LVL (no overhang; beams sit flush on posts) • Cross‑ties: 90×45 mm timber battens at ¾ height for trellis mesh • Span: Approx. 4 m • Load: Decorative only (festoon lights + ivy canopy) Beam‑to‑Post Connections • Beams must sit flush on top of posts with no overhang. • Concealed brackets or half‑housing joints required. • No visible external pergola brackets. • Once painted, the beam and post should appear as a single continuous element. Ledger Board (House Wall Connection) • Supply and install a 90×240 mm LVL ledger to match beam dimensions. • Ledger must align perfectly with the beam’s top, bottom, and front faces for a seamless look. • Two circular penetrations must be cut through the ledger to allow existing wall light cabling to pass through cleanly. • Ledger top must be either:• Bevel‑cut (splayed) to shed water, or • Covered with slim flashing to prevent water pooling. • Final ledger colour to be either Monument grey or off‑white (to match house wall), depending on final design choice. Footings • Four concrete footings already installed. • Posts to be fixed using bolt‑down stirrups sized for 90 mm posts. Finish • Clean architectural detailing. • All timber to be painted Monument grey or off‑white depending on final design direction. Access Access to the courtyard is via the garage, through a single door. No internal house access required. Ideal Installer Experienced with LVL beams, concealed joinery, architectural pergola detailing, and precise alignment work.

We need someone who can assistance us with assembling and securing a 3M x 3M aluminium powder coated pergola. We are particularly looking for someone who also has experience with fixing the pergola to a concrete/aggregate base? Needs to be a neat job. My husband and I can assist with assembly https://www.bunnings.com.au/mimosa-3-x-3m-lava-portsea-louvre-semi-permanent-gazebo_p0372487

Need a pergola to be painted.

Safe removal of shed and pergola, Inc disposal of timber and metal sheeting. Shed partially removed already. Temp solution for back fence. Sorted electricity, and finalising getting the roof tested for asbestos this coming week.

I got everything just need installer so let me know

Need to install pergola in my backyard already git all parts just need installer got bolts everything

Finish painting pergola frame - chocolate brown | URGENT | Wed/Thu The job: Finish painting the steel pergola frame in chocolate brown. I've completed half the frame—you'll continue the same colour and finish to completion. Straightforward continuation work, no prep needed. What you get: Paint supplied (chocolate brown—see attached photos of existing work) Tools: bring your own OR I can supply Clear reference photos of colour/finish to match Outdoor poolside setting, good access Timeline: Wed 23 Sept or Thu 24 Sept (ideally same-day or next-day completion) Budget: $200 AUD Why this is quick cash: No colour decisions 4–5 hours, tops Materials ready to go Flexible on tools—whatever works for you

set mice traps seen mice in the garage and pergola area

Pergola slat on roof partially rotten due to gutter blockage. If it possible to cut it off and replace partially.

Job 1) replace existing rotted pergola post.

Erect a 3.5 x 6m pergola. Was purchased as a kit; needs to be installed. Back 2 posts to be concreted into ground (holes dug already) front posts to be bolted to concrete. Note this is not a simple pergola, will need to be installed by someone with experience

Repaint Outdoor Timber Pergola – Maribyrnong Looking for an experienced painter to repaint my recently built 8m x 5m outdoor timber pergola in Maribyrnong. The pergola has recently been painted green, however I’ve decided to change the colour to a warm off-white/cream. The job will include: * Preparation/light sanding of the existing painted surface as required * 1 coat of suitable primer/undercoat * 2 coats of exterior topcoat * Painting all posts, beams and roof rafters * Careful painting around the newly installed polycarbonate roofing and surrounding areas * Clean and tidy finish The pergola is new and the existing paint is also very recent, so the timber is in good condition. I’m happy to supply the primer and paint, or please specify in your offer if you would prefer to supply materials. Please include in your offer: * Total labour cost for the completed job * Estimated time required * Whether equipment/materials are included * Your painting experience/relevant reviews Photos attached showing the pergola and current green colour.

Dig holes for Pergola Post - 3 Hole x 2 Feet each . Ineed to install the posts, have the cement and everything. Bring your own tool to make holes

Looking for an experienced roofer to supply and install a new roof for a L-shaped pergola structure. Current Status: • The timber framing and posts are fully built and ready for roofing sheets/battens/ flashings. • Site is located in Hampton Pergola Dimensions (L-Shape): • Main long edge: 9,910 mm • Side long edge: 7,400 mm • Depth/Widths: 2,550 mm & 2,500 mm (Please refer to the dimension sketch attached). Scope of Work: • Supply and install roof purlins/battens (if required). • Install roofing sheets + wall apron flashings + capping. • Supply and install guttering and downpipe setup. Roofing Preference: • We are currently deciding between Full Polycarbonate Sheets (e.g., Laserlite 3000) vs A Combination of Colorbond + Polycarbonate skylight strips. • We would welcome your professional advice on site regarding light, heat insulation, and aesthetics. Requirements: • Experienced with outdoor pergola roofing, flashing, and gutter installation. • Must have own tools, safety equipments, ladder/scaffolding Image 1 is rough sketch of the size Image 2-3 are current structure Image 4-5 are what kind of effect I want (welcome your expert opinion) This is a task to look for the right person to come onsite to provide quote based

Pergola with single post and fascia install. 2 sides will be fascia mounted/fixed. I have the pegola already, dimension are 4160L x 1990 W. Added example of pergola type

I want to build the pergola on 2 places in my house I’m happy to help to build it . But I need some one who has an idea of how and where we can buy all the items . I’m good with wood and have a knowledge about pergola but need some advice and hands to help build it. Regarding the price we can talk about it.

Want to close off my pergola. Still want to keep natural light coming in potentially covering roof with polycarbonate or colourbond. Frame needs sanding and painting as well. Rough measurements 2600 height, 4500 width, 1900 depth. Can provide materials too if required

Need a licensed electrician to complete an outdoor pergola heater connection at a residential property in Tarneit. There is already dedicated electrical wiring running from the main switchboard to an external junction box. The job involves connecting from this junction box to a new outdoor power outlet suitable for a 15A plug-in heater. Key details: Existing dedicated cable already installed from switchboard to junction box Need supply connection from junction box to new outdoor weatherproof power outlet I already have a 15A power outlet available (if suitable for use)