Find a local electric car service expert in QLD

Hi, I’m looking for an electrician to check an issue with my food trailer. The trailer’s power tripped last week and I’m not sure what caused it. I need someone to inspect the wiring, power inlet, and internal circuits to identify the fault and make any necessary repairs. The trailer is located in Redbank Plains.

I have a 2007 vw Passat 2.0 tdi car where the electric seat control and the seat heating is not working. I have checked the fuses which are still good and the airconditioner stopped working too. Would be great if someone could have a look at it

Passenger side window won’t go back up. Unsure of fault. Just need window to go back up, doesn’t need to work. If able to repair back to working condition, great.

Need my scania trucks window fixed

Remove old and install new 2 x 120ah lithium batteries new inverter new ac charger new dc charger

Please quote on: camper trailer has a standard 15 amp plug in fitting to take 240V power (eg caravan park). I just need the wiring done from the inside of this fitting to a new (already purchased) Powertech double RCD protected GPO, which sits in an existing box which bolts onto the camper. Very simple and fast job, there was a standard double GPO already installed previously. The new GPO has been purchased, just labour time involved, estimate 5-10 minutes max, please quote

Hi. We have a few campers that require 240v certification by a qualified electrician. Normally we do this at our workshop, but a previous agent we employed forgot about this and so we have a gap. Looking for someone(s) who is flexible and works across Gold Coast / Brisbane areas and able to drop into a few addresses. We have photos of builds, materials used, schematas etc. and these are pretty simple setup. We have plenty of others that are certified. Hoping to find someone reliable rather than approach multiple businesses.

Scope of Works – Toyota Coaster Motorhome 240V Electrical Fit-Off Location: Ashmore, Gold Coast Seeking a licensed electrician with RV, caravan or motorhome experience to complete the 240V AC fit-off in a Toyota Coaster conversion. Most cabling is already installed. Spare cable and conduit are available if required. Work should comply with AS/NZS 3001 where applicable. Owner Supplied • 5 × double-pole double GPOs • 1 × double-pole quad GPO • 1 × GEYA W2R-100 Automatic Transfer Switch (ATS) Scope • Inspect existing 240V wiring. • Complete any remaining wiring for a safe, compliant installation. • Use existing cabling where practical. • Install and terminate: o 5 × double GPOs o 1 × quad GPO o 2 × external weatherproof single GPOs:  Shore power inlet  External convenience outlet • Install and wire the supplied GEYA W2R-100 ATS to automatically switch between shore power and inverter, following manufacturer instructions. • Supply and install suitable switchboard/enclosure and circuit protection (RCD/RCBO as required). • Preferred layout: two final sub-circuits (left and right side outlets), or advise if a better arrangement is recommended. • Test and commission the installation, including ATS operation, polarity, earth continuity and RCD/RCBO functionality. • Provide any required electrical certification/compliance documentation. ATS Information Product: https://www.geya.net/product/w2r-automatic-transfer-switch%EF%BC%88ats%EF%BC%89for-pv/ Manual: https://www.geya.net/wp-content/uploads/2021/02/W2R-regular-Automatic-Transfer-Switch%EF%BC%88ATS%EF%BC%89User-Guide.pdf Budget: $250. If you believe additional work or parts are required, please provide a fixed-price quote including all materials.

No spark, dodgy wiring. Was going a yr ago went hunting5 days no problems now no spark

Get the motorcycle started. Tried with jumper leads but doesn't work. Tried with a new battery but seems to be disconnect. Racq said, may be corroded power leads. Not sure. Yamaha Vstar 1100 2008

Need an electric roller installed on my ford ranger * DO NOT HAVE THE ROLLER* • preferably a key with the open shut on my original ford key • light inside with roller if possible • I have a sports bar also at the back

Hi Spiky, my ute tray has a 12V socket (cig-lighter type). I want the pump to plug straight into it instead of the battery clamps. Cut off the red & black croc clips. Fit a 12V cig-lighter plug that suits the tray socket. Keep polarity right: centre = red (+), side = black (–). Keep the inline fuse on the red wire. Make it tight and weatherproof. Pump draws under 15A, so the socket's fine.

Restoring a 1989 Ford F250, RHD-converted, 302 Windsor EFI with C6 auto. I've handled bodywork, cosmetic restoration and some mechanical fitment myself, but need someone who genuinely knows these trucks for the mechanical/electrical side. NEED HELP WITH: - Engine bay assessment — unidentified components/routing on a 302 Windsor EFI - Alternator/charging wiring — no harness diagram survives the RHD conversion - Unlabelled connectors/wiring in engine bay and firewall needing ID and correct termination - AC routing — no firewall penetration yet for HVAC lines & Condensor - Suspension/steering — ball joints, radius arm bushes, sway bar bushes (parts on hand) - Brake system check before first fluid commitment - Pre-start sign-off — fuel system, belts, general check before first start IDEAL PERSON: - Experience with classic American V8s/Ford F-series, ideally RHD conversions - Comfortable fault-tracing without a full wiring diagram - Happy to explain as they go, not just take it away On-site, Cleveland QLD, truck not driveable. Ongoing work preferred. Quality parts on hand. Flexible with weekdays/ weekends

I need someone to inspect and repair the electrical wiring on my 4x6 box trailer. The trailer plug is damaged and the lead/wiring may need to be replaced. I do not have a replacement lead or plug, so the successful tasker will need to supply any required parts. The job includes: * Inspecting the trailer wiring and lights * Replacing the damaged plug and lead if required * Repairing any damaged wiring * Testing all indicators, brake lights and tail lights to ensure everything works correctly Please include labour and parts in your offer, or clearly state any additional parts costs.

seeking an electrician to replace alternator and check the ignition on a tractor

Car: Ford Falcon FG G6E, auto Problem: the shift selector cable bushing at the gearbox end has let go (a common Falcon fault). RACQ has already attended, confirmed it's the bushing, and manually put the car into neutral. Before that the shifter was sliding through P/R/N/D doing nothing and the dash was stuck on P. Just need the bushing repaired. It's in an underground residential carpark in the Brisbane CBD city - height clearance is 2m. There's a couple of security gates so I'd need to jump in on street level and guide you down.

I got a new number plate holder and I need the numberplate light wired up so it can be plugged into my bike

Injector pump not receiving power. Auxiliary battery not charging

My John Deere ride on LT180 is running but recently it just stopped. I charged the battery and won't even turn over when I turn the key. Looking for someone to come and take a look at who knows how to fix electrics/starter issues

Require someone with experience to install an electric roller cover from OCAM industries on a 2024 Ford Ranger Raptor.