Find a cladding professional in QLD

Needing an extra hand tomorrow installing Easylap cladding sheets. A couple of windows, external door jamb and minimal framing. Must be experienced in these areas. Good hourly rate happy to negotiate rate and possible extra work.

Kitchen bench cladding, to apply cladding panels on a kitchen bench

Needing to mount WPC (wood finish) on an exterior courtyard straight wall. Wall Measurements are - 3.73m x 1.8m Product measurements are 200mm x 1.8m Roughly 19 sheets to mount. Cutting only one WPC (Wood Plastic Composite) and beams have already been purchased . Just need you with the tools to connect all items for a finished product. Photo of the work area is attached as is the product sample

Looking for a qualified carpenter to fit the last couple of sheets and soffit on a two story Queenslander in Albion. The scissor lift is on site.

Need to install Acoustic Panels, in the area with red paint and then from red to the area next to display fridge. 12 Panels of 3M ones, and 9 Panels of 2.7M ones.

I’m looking for someone experienced with carpentry/WPC cladding to complete an outdoor TV/fireplace feature wall in Collingwood Park. The wall is already framed and sheeted. I will supply all materials, including: * WPC cladding/panels * Trims/corner trims * Exterior sheeting * Timber/framing materials * Adhesive/fixings as required Approximate wall areas: * Front wall: 2.57m W × 2.5m H * Side wall: 0.8m W × 2.5m H * Return: 0.25m W × 2.5m H * Back wall: 2.57m W × 2.5m H * Other side wall: 0.8m W × 2.5m H The job includes installing the WPC cladding neatly to all required faces and cutting around the existing TV recess and fireplace opening. There is also an open gap at the top between the front and back walls, which needs to be framed/sheeted and closed before finishing. The existing top edges are slightly uneven, so I would also like the finished top edge to be made straight and consistent in height where required, without unnecessary rebuilding. I will supply all materials. I am looking for a fixed labour price for the complete job, not a daily rate. Please only make an offer if you have experience with WPC cladding/carpentry and can achieve neat cuts, corners and finishing. Photos attached showing the current condition and the cladding being used.

Looking for carpenter who can assist my builder in putting the remaining AXON cladding on to the upper second story addition level in Southport. 85% of the cladding is on- just one section of the house wall upstairs and back section needs to be finalised. 55sqm left to be done Around 25 sheets of cladding or so Some cement fibre trims also to be fitted around remaining windows Full scaffolding and edge protection on site. You will be expected and required to have your own tools. Thank you

I’m looking for an experienced carpenter (or patio/pergola installer) to line/cover the underside of my patio ceiling for a clean white finished look. Current situation Patio has exposed joists/rafters underneath (see photos). Downlight wiring has already been installed by a licensed electrician (wires are ready). I now need the ceiling lined and finished underneath. What I need done Advise best material for outdoor patio ceiling (white, clean look) – I’m open to fibre cement sheets or PVC lining panels. Install battens if required. Supply & install ceiling lining (or install only if we agree I’ll supply materials). Cut-outs/holes for the existing downlight locations. Neat edge finishing/trims so it looks professional. Please include in your offer Your recommended material option (PVC vs fibre cement) and why. Whether your quote is labour only or labour + materials. Estimated time to complete. Any photos of similar patio ceiling lining work (if available). Location: [Springwood QLD 4127] Access: Easy access under patio. Thanks! Nathan

Paint the interior of the new bedroom. Paint only the plasterboard ceiling of the carport (the carport is not enclosed/covered). Paint the exterior cladding of the new studio. Paint a couple of doors and windows.

So I attempted to remove this PVC cladding off which is around my house as there is nice timber VJ panels underneath. I need someone to quote to remove it all put things back in it place as you would need to unscrew stuff, like ducted air con cables,solar power unit etc and put back onto the wall when the old PVC panels removed. The PVC cladding is screwed in too as I did try using a cladding tool but it hard when things are screwed in

A section of exterior timber/cladding came off my house during strong winds and needs to be repaired/replaced. We also have a water leak coming through the ceiling inside the house. We’re not sure where the water is getting in from and would like someone to inspect it and identify the cause. The damaged area is quite high — approximately three storeys from ground level, as the granny flat is located above the garage. I’m looking for an experienced carpenter/builder who is able to safely work at this height and provide a quote for the repair. Please see attached photos for the damaged area Please provide your quote based on the photos and access requirements.

Looking for a professional to replace the cladding on the outside of my house just the sheets you see looking to change it to the timber cladding Roughly 26m to be replaced. Happy to purchase myself will need it fitted and waterproof as you can see the rust. There’s no waterproof there looking for a professional that knows the proper way to fit this waterproof it so the elements aren’t getting in the house..

We have a 9m x 7m granny flat that needs timber batons screwed to purlins then James Hardie weather board cladding added. Quote only

External Recladding – Beenleigh Looking for an experienced carpenter/cladder to remove the existing tin/metal cladding from the lower section of our house and replace it with wide-groove vertical fibre-cement cladding, similar to James Hardie Axon Smooth 400. Approx. area: 18 m long × 2.4 m high. Scope: - Remove existing tin cladding - Remove existing timber piece where required - Check framing and advise of any repairs - Install wall wrap/membrane and flashings as required - Install new wide-groove vertical fibre-cement cladding - On the rear wall, clad right up to the top/underside framing to hide the existing gaps - Finish neatly around windows, doors, downpipes, A/C and other penetrations - Leave weather-tight and ready for painting - Existing upper weatherboards are staying - Remove and dispose of old cladding Photos of the current walls and concept images of the finish we want are attached. Please include your experience, QBCC details if applicable, cost including materials and availability. Located in Beenleigh, QLD.

I have 60 m2 Hardies Newport cladding to install in Robina It’s a single wall 13m long x3.8m high, to be installed off scaffold All materials will be supplied

Set out 40mm steel battens Attatch klip lok fixings screws provided Attatch klip lok sheets provided Add flashing provided Tiny house is 7mx2.4m , 4.3m high

Looking for someone to install the cladding on our living area.

External wall Eastern elevation cladding wall to be repainted 20m x 8m total area

My husband is doing it himself so I'm trying to get extra hands to go faster. Putting cladding stones like photos on the outside wall.

Finish off cladding the side of the house boards onsite