Find a local Tasker to replace your engine near you

Hi, I need a qualified person change the engine oil and filters on my car. Location: I can drive to your place/anywhere you suggest. Parts: I already have the engine oil and air/oil filter. You will only need to supply the labor and your own tools (jack, axle stands/ramps, oil drain pan, filter wrench). Vehicle Details: 2014/15 VW Passat Sedan 1.8tsi Requirements: Clean and tidy job Safe disposal of used oil and filter Check of fluid levels after the change. Please let me know your availability when submitting an offer.

I have a Bluetti Charger 2 that I've bought and would like to install on my Subaru Outback. The product is pretty simple to install but needs a cable routed from the battery in the engine bay through to the passenger cabin. Drilling may be required, but hoping to avoid.

Hi, I am reporting this, health issues impacted me responding to previous messages. Apologies for any inconvenience or stress this may have caused those who sent a message. .. I'm unable to access old messages hence repostingthe same ad here. .. Unfortunately I was sold a dud RAV4 with an engine issue. Wondering if there's anyone interested in doing the rebuild with the kit or if I can find an engine, to replace it. I'm not in a rush, so happy for you to do it on the side of other work.

Just engine oil and oil filter change

Looking for a mechanic or experienced home mechanic to test and remove a 5S-FE 2.2L engine from a 1998 Toyota Celica located in Ingleburn. The motor is currently still installed in the car and running.  Requirements: 1. Pre-Removal Testing: Before unbolting anything, start and run the engine, perform a quick compression test across all 4 cylinders, and check for any unusual noises, smoke, or milky oil/coolant.  2. Engine Pull: Carefully remove the bare engine long block using an engine crane.  3. Equipment: You will need to bring your own engine crane, compression tester, and standard mechanic hand tools/sockets.  Location: Ingleburn, NSW Date/Time: Flexible depending on seller availability.

Changing self-buy engine oil, filters, 4 braking pads ,rotors parts (Yr 2018 Peugeot 5008 1.6T petrol, 73000km)

I need the engine oil drained and filled again - I’ve put too much in. Cheers

Vehicle: 2006 Ford BF Fairmont MkII (NA Barra) Task: Basic engine-health upgrade & parts replacement Parts Supplied (all fluids provided + pans etc): • Aluminum radiator • New expansion tank • Silicone coolant hoses • Solid band ring clamps • Thermostat + gasket • Proflow trans cooler (braided lines) • Aeroflow Alternator & replacement plug • Drive belt • 2x cam sensors • Upgraded power steering line • Red/black OFC cables for overlay, copper lugs & fuse holder • SAAS throttle controller Note: I can remove front bumper before you arrive so you can avoid bodywork. Please have: • Trans fluid pump & OBD2 scanner for ZF temp check • Soldering iron (alternator plug) & hydraulic wire crimpers (lugs) I will provide the complete parts list & project brief via text once assigned. Please confirm your experience with the Barra platform and BA/BF chassis when offering. Cheers.

- 2014 Toyota Corolla (pictured) - Engine swap with 60,000km - Supplying all required associated needs (spark plugs, water pump etc.)

I have a Rolls-Royce B60 Engine thats started foulung plugs really fast. need to work out if its timing or carbs. Im after someone with some experience on similar engines.

I have honda jazz 2009 1.4L engine car and i purchased recently horn from eBay but when i try to replace it didn’t work. So I can’t figure out what is wrong with horn. I need mechanic who can help me to fix the horn.

Looking for a qualified, licensed mobile mechanic to perform a diagnostic inspection on my 2006 Hilux 4.0L V6 4x4 .The engine recently overheated from a water pump leak and is now running rough with a ticking noise. My dad did a basic compression test and found one cylinder has low compression. The top end of the engine is currently half-disassembled (valve covers and intake plenum are off). I need a professional to come out to my garage to perform a Cylinder Leak-Down Test and use a Borescope Camera down the low cylinder. To determine if the low compression is just a blown head gasket, or if there is More damage to the cylinder walls or pistons Thanks Kyle

The engine was put upside down, does not start Most likely needs new spark I come transport it anywhere to you

1. OBD-II Diagnostic Scan. 2. Inspect engine to pinpoint source of the noise. 3. Repair the Fault If major repair is needed, cost will be seperate.

GWM Cannon 21'- engine has supposedly failed. Require a licenced mechanic to remove existing and install new. We will supply the new engine. Can we please include a service also. Thank you

Looking for a mechanic experienced with these cars. Will be installing an SR20DET with five speed box into S13 rolling shell. looking to get it done across a few days and need guidance and assistance in getting everything right.

Hey everyone, I need someone install the rear engine mount for 2018 Ford Custom I already got the part, Car already lifted. I just hurt my arm so i cant do it anymore. I remove old one.

My VW shows this warning light, it doesn’t always appear. Please help me to fix problem

A bolt has broken off from a side mounting bracket into my engine. I want to get it drilled out and preferably without removing the bracket or dropping the engine. Let me know what’s possible, cheers