Driveway Repair & Installation Jobs in Sydney Northern Beaches

Browse through over 500 Driveway Repair & Installation Jobs.

See what you could earn

$0

per month

Based on average building & construction task prices. Actual marketplace earnings may vary

Why join Airtasker

Join Airtasker

Building & Construction tasks in Sydney Northern Beaches

Check out what tasks people want done near you right now...

Quote for BMW series one E 87 N47 engine timing chain replacement for drivie in and drive out service must be Melbourne located

Thu May 08 2025

about 24 hours ago

Open

Plumber have to relocate the internal plumbing for Water Cop to lower water meter on the drive way

Byford, Western Australia

Thu May 08 2025

1 day ago

Open

New set of Keihin FCR33mm fitted to a 1982 Kawasaki Z1300. I need someone to tune them properly. Currently tunning way too rich.

Sun May 04 2025

6 days ago

Open

A joiner to supply and install a tv wall / bookshelf wall Wall is gyprock with timber stud per first image 2400 high x 4000 long Cabinetry can be 350 deep - 400 and match the nib wall depth Quote to include Material supply Remove old cornice if in the way Install cabinetry and supply cutouts for gpo in wall Caulk wall and cabinetry junction if needed Exclusions Power disconnection I will supply Painting Cabinetry handles Image 2 is the inspo but I’m open to alterations

St Ives NSW, Australia

Sun May 04 2025

6 days ago

Open

The drawings are already prepared, soil test is under way, and I need this certification as soon as practical to lodge my building application to York Council,WA. Sign off specifics are: Registered engineer in WA to sign off on the following: Concrete slab on ground for single story house as per as2870 Roof and wall steel framing design as per as4600 Statement of compliance to Australian standard 1170.4 for seismic actions Statement of compliance to Australian standard as4055 for wind actions Attached carport, stand Alone carport and attached steel verandah as per as4100 Other services I require are energy rating/ certification and overall certification of the build as a Building Surveyor would do. Can you help with these also? Thank you

Wed Apr 30 2025

9 days ago

Open

We have saw cut part of the driveway for installation of a stormwater pipe. Roughly 500mm wide by 18m Needs to cleaned up and concreted

Frenchs Forest NSW, Australia

Thu Apr 24 2025

15 days ago

Open

I am looking for someone who is very familiar with glassing techniques used in making surfboards with epoxy resin. I am an artist and need panels - rectangular pieces of EPS foam ( as large as 2m x 1.5m) glassed and sanded to a Matt finish - same as surfboards. I will supply all materials but happy to discuss further if any changes needed. I have been doing this myself for some years and there are some issues that come up - such as folding edges etc but I have worked around this and will explain how. Other than that it is very straightforward as they are just large flat surfaces. Adjustments will be needed as obviously regular glassing stands and set up probably won’t take the size of the panels so will need a different surface. I can have/can make a set up to do all the work at my place however I am in the southern highlands NSW so am assuming it will be easier ( and my preference) to bring the panels to wherever you are - probably coastal? Am open to travelling a fair way - Newcastle is about 3 hours from here - happy to go this far or a bit beyond and the same distance south from the Southern Highlands of that helps. I have taught myself to do this but don’t have the time to dedicate to this and it’s also not my specialty so know I won’t/dont get as good a result as someone who is well practiced etc! Happy to discuss prices etc. I’m looking at needing around approx 4 - 7 panels to start with in varying sizes but will be ongoing job if we are both happy with it. I won’t have the panels ready for 3-4 weeks approx.

Manly NSW 2095, Australia

Wed Apr 23 2025

16 days ago

Open

Concrete small area on the front driveway

Dee Why NSW 2099, Australia

Wed Apr 23 2025

17 days ago

Open

A very fine pitched (0.3-0.5) 24-way flap-up horizontal ZIF ribbon cable connector (Hirose?) was damaged by an installer on a brand new PCB inside a home EV charger. I need the connector component replaced by someone with the right tools and skills and who can possibly also source the component.

Wed Apr 23 2025

17 days ago

Open

Browse all tasks

Last updated on 9th May 2025

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

We've got you covered

Whether you’re a posting a task or completing a task, you can do both with the peace of mind that Airtasker is there to support.

Airtasker’s insurance cover

Browse similar jobs in Sydney Northern Beaches

Drafting

Patios

Driveway Repair & Installation Jobs in Sydney Northern Beaches

Browse through over 500 Driveway Repair & Installation Jobs.

See what you could earn

$0

Building & Construction tasks in Sydney Northern Beaches

Replace timing chain (Whole Kit)

Plumber to prework for water cop to lower water meter

Motorcycle keihin carburetor tuning

Joiner for tv wall / cabinetry wall

Structural certification of house in West Australia

Concrete installation

Fibreglassing - Surfboard glassing - epoxy resin sanding etc

Concrete a small area

Fine PCB-level electronic component replacement