Hire a trusted shelf hanging expert in NSW

Carpenter to build concealed door Build and install a concealed door 2m wides 2.6 high with mirror and side architectural panels see inductive image I will pay for all materials including Mirrors you must organize them especially the hinges you Must have all required tools and be skilled in carpentry and joinery

Looking for an experienced handyperson to supply tools and securely install 3 String shelving brackets onto a plasterboard office wall. - Shelf Type: String shelving bracket (the shelves are interchangeable) - Wall Type: Gyprock / plasterboard over timber studs (will require locating studs or heavy-duty cavity anchors). Requirements:Must bring a stud finder, spirit level, drill, and appropriate heavy-duty wall fixings/anchors (or let me know if I need to buy them beforehand). Ensure everything is perfectly vertical and securely anchored so it won't pull out of the Gyprock under weight. Clean up any minor mess afterwards. Please include your experience with wall mounting in your offer. Thanks!

6 floating shelves and 1 flat pack 2 door cupboard to install

Shell ornament I want hung from the ceiling of outdoor balcony above outdoor table

Two part job, sourcing and installing wall hung shelving for this garage wall, and also do a few tip runs if possible. Better if you can come right now! But flexible otherwise

Task title: Install wardrobe shelves and curtain tracks I’m looking for someone to install shelves inside my walk-in wardrobes and sort out the curtain tracks. Please inspect the attached photos and source and install the correct curtain track or mounting brackets needed for the setup. I already have the curtains, so I don’t need to buy curtain fabric. Please let me know if you can supply the shelving materials and any track fittings, and include the cost of materials in your offer.

Hang two peices of 3m woods as shelves and two fishing rod wall holders on garage walls. Need to make sure they are attached to inside gyprock studs.

Mounting and installation job I need two items securely mounted on an internal wall: 1. Oak floating shelf
Install a solid oak floating shelf into the wall studs (and gyprock). Stud screws have already been purchased and will be supplied. 2. Large painting
Mount a 1500 × 1000 mm painting directly into gyprock. Please quote for both jobs, including any additional fixings or hardware required for a solid, level finish.

I have an empty section in my existing wardrobe and would like white built-in shelves installed, as shown in the attached photo. I’m looking for someone experienced in wardrobe shelving/cabinetry who can: * Measure the space * Recommend the appropriate shelving material and dimensions * Advise me on exactly what materials and hardware to purchase * Install the shelves securely with a neat, built-in finish I will purchase the materials based on your recommendations. Please quote for labour/installation only. I’d prefer someone with experience installing built-in wardrobe shelving.

Need one shelf to be screwed into the wall. I have the wood and the brackets for the shelf . Pine Shelf size 123cm x 29cm x 2cm I can swap the brackets at Bunnings before job if required

Installation of an ikea shelf into wall (brick)

I have 3 x 1700mm x 250mm x 35mm timber shelves to be installed on a stud gyprock wall. I want them to be floating shelves. Job will require recommending and supplying appropriate floating brackets (we live close to a Bunnings). The shelves need holes drilled also. Seeking professional carpenter or equivalent who can do the job ideally on a weekend or Friday.

Put up brackets to hang two shelves in laundry (have supplies) Re hinge and hang garden gate (have supplies) Fix loose screws/spot they have been screwed into for dishwasher - need to be longer or adjusted to better fit and stay securely in place Ideally want this done asap.

Looking for an experienced handyman to install the following: • 2 × IKEA floating shelves – 120cm × 20cm • 1 × IKEA floating shelf – 80cm × 20cm • 1 × pegboard • 2 × Holman hose reels • 1 × small picture frame Location: Marsden Park, NSW Timing: Must be completed today I have all the fixing but don’t have appropriate screws Please only make an offer if you are available to complete the job today.

We're looking for a licensed electrician to install a new power point above our shelving. The cable can be run down from the ceiling cavity directly above, so it should be a straightforward installation. We expect the job to take around an hour, and our budget is approximately $500. Please send through your offers. **Licensed electricians only, please** Thanks!

i need 3 sheves and one peg board install on a brick wall. Please bring screw and consider the right drill part for a brick wall

Install 4 shelves to the tiles wall and 1 rack shelves to the kitchen table (stainless steel material) in take away shop at Eastwood. Need it to be done before 10am.

Need a shelf installed above an oven, and need it to have a black glass front, to match the oven.

Need a licensed sparky to install a Shelly Pro 3EM-3CT 63 (3-phase energy monitor) into my residential switchboard this Saturday. The job: Install 3 × split-core CT clamps around the 3-phase mains cables between the meter output and main switch Mount the Shelly Pro 3EM unit (DIN rail or adjacent) Wire a 240V AC feed to power the unit (from a spare MCB or existing circuit) Verify it powers up and CTs are reading What you DON'T need to touch: The Endeavour Energy revenue meter (Elster A1100), sealed, stays as is Service fuses Solar inverter or array wiring Any existing circuits What's already here: 3-phase board, dual supply (grid + rooftop solar) Elster A1100 meter, Endeavour Energy network Tenby Cables switchboard, Left + Right modules The Shelly unit and all 3 CT clamps — I have everything, just need it installed I'll provide: Full installation guide with wiring diagram (already prepared) Photos of the switchboard for your reference (attached) The Shelly Pro 3EM unit + 3 CT clamps (all supplied) You'll need to bring: Short length of 35mm DIN rail if there's no spare space on the existing rail (board looks fairly full, may need to mount a small rail segment on the back panel) 1 × MCB (6A or 10A) to protect the Shelly's 240V power feed Short lengths of wire for the 240V feed (L + N to the unit) Location: Kellyville Ridge, NSW When: This Saturday — flexible on time, morning or afternoon Budget: $150 – $200 This is a straightforward install, no modifications to existing wiring, no meter work, just clamp-on CTs and a small monitoring unit. Should take 30-45 minutes for anyone familiar with switchboard work. Must hold a current NSW electrical licence. Happy to see your licence number before confirming. Cheers!

Install 6 shelves into stud wall. Gap is approx 50cm wide. Will need to supply shelves will cover cost for those separately