Hire a trusted shelf hanging expert in NSW

2x shelves, into brick. 2 x Mirror to be hung 2 x pin boards to be hung. I will be there to assist and position with the installation.

The shelter fell from strong wind need it re installed

Hi, I’m looking for an experienced handyman/specialist to install a King Living shelving system. The shelving has floor-to-ceiling posts that need to be securely fixed to the ceiling. You will need to be able to locate the ceiling studs/joists and ensure the posts are properly and safely secured. Please bring the appropriate stud-finding equipment and tools required for the installation. Experience installing similar shelving systems or King Living furniture would be preferred.

I need a shelf supplying and installing

I have some off cuts from new kitchen install. I want to cut and install shoe shelving in bottom of wardrobe. I think there’s enough for 6 shelves (3 on each side) - I have the wood and brackets. Need someone to measure and cut and install the shelves in the wardrobe. I’m free next Friday afternoon or anytime over the weekend (weekend 10th October)

Installation of an ikea shelf into wall (brick)

Hello I need help to install: 1. 2 shelves inside 2. A small clothes line outside (similar to a shelf installation) 3. A small bookshelf in the space shown in the attached photos (I don’t have shelves for this yet) Thank you!

i need shelves to be doen in a wadrobe have teh board for shelevs and assemble a cabinet

Looking for a handyman to complete a few jobs at our apartment: 1. Install wall shelving unit – mount the metal shelving unit pictured securely onto the living room wall. Shelving is approx. 1600mm high. 2. Install fold-down balcony table – securely drill/mount the fold-down table to the balcony wall. Mounting instructions included. 3. Adjust built-in cupboard doors – raise the cupboard doors slightly so there is enough clearance to place a rug underneath them. They have adjustable concealed hinges (pictured), so hoping this can be done through hinge adjustment rather than modifying the doors. All items are already here. Please bring appropriate tools, drill bits, fixings/anchors etc. for the different wall surfaces.

I have 3 x 1700mm x 250mm x 35mm timber shelves to be installed on a stud gyprock wall. I want them to be floating shelves. Job will require recommending and supplying appropriate floating brackets (we live close to a Bunnings). The shelves need holes drilled also. Seeking professional carpenter or equivalent who can do the job ideally on a weekend or Friday.

Put up brackets to hang two shelves in laundry (have supplies) Re hinge and hang garden gate (have supplies) Fix loose screws/spot they have been screwed into for dishwasher - need to be longer or adjusted to better fit and stay securely in place Ideally want this done asap.

Looking for an experienced handyman to install the following: • 2 × IKEA floating shelves – 120cm × 20cm • 1 × IKEA floating shelf – 80cm × 20cm • 1 × pegboard • 2 × Holman hose reels • 1 × small picture frame Location: Marsden Park, NSW Timing: Must be completed today I have all the fixing but don’t have appropriate screws Please only make an offer if you are available to complete the job today.

We're looking for a licensed electrician to install a new power point above our shelving. The cable can be run down from the ceiling cavity directly above, so it should be a straightforward installation. We expect the job to take around an hour, and our budget is approximately $500. Please send through your offers. **Licensed electricians only, please** Thanks!

i need 3 sheves and one peg board install on a brick wall. Please bring screw and consider the right drill part for a brick wall

Install 4 shelves to the tiles wall and 1 rack shelves to the kitchen table (stainless steel material) in take away shop at Eastwood. Need it to be done before 10am.

Need a shelf installed above an oven, and need it to have a black glass front, to match the oven.

Need a licensed sparky to install a Shelly Pro 3EM-3CT 63 (3-phase energy monitor) into my residential switchboard this Saturday. The job: Install 3 × split-core CT clamps around the 3-phase mains cables between the meter output and main switch Mount the Shelly Pro 3EM unit (DIN rail or adjacent) Wire a 240V AC feed to power the unit (from a spare MCB or existing circuit) Verify it powers up and CTs are reading What you DON'T need to touch: The Endeavour Energy revenue meter (Elster A1100), sealed, stays as is Service fuses Solar inverter or array wiring Any existing circuits What's already here: 3-phase board, dual supply (grid + rooftop solar) Elster A1100 meter, Endeavour Energy network Tenby Cables switchboard, Left + Right modules The Shelly unit and all 3 CT clamps — I have everything, just need it installed I'll provide: Full installation guide with wiring diagram (already prepared) Photos of the switchboard for your reference (attached) The Shelly Pro 3EM unit + 3 CT clamps (all supplied) You'll need to bring: Short length of 35mm DIN rail if there's no spare space on the existing rail (board looks fairly full, may need to mount a small rail segment on the back panel) 1 × MCB (6A or 10A) to protect the Shelly's 240V power feed Short lengths of wire for the 240V feed (L + N to the unit) Location: Kellyville Ridge, NSW When: This Saturday — flexible on time, morning or afternoon Budget: $150 – $200 This is a straightforward install, no modifications to existing wiring, no meter work, just clamp-on CTs and a small monitoring unit. Should take 30-45 minutes for anyone familiar with switchboard work. Must hold a current NSW electrical licence. Happy to see your licence number before confirming. Cheers!

Install 6 shelves into stud wall. Gap is approx 50cm wide. Will need to supply shelves will cover cost for those separately

I purchased some floating shelves and need somebody to drill the necessary holes in brick walls to help install them. Thank you!

I have a painting that needs to be hung on the wall and a small floating shelf to be installed. The wall is gyprock and I think concrete might be behind the gyprock so a hammer drill and wall plugs could be required however I’m not 100% sure. It’s a small job that should take 60 minutes or less.