Find trusted glazing experts in NSW

Bought 3 new 180cm x 90cm double glazed windows. Those need to be installed and I am looking for professional help for my carpenter. Ideally looking for someone with heaps expertise and doing this anyway full time to assure existing timber frame can stay and insulation/foam etc be done properly. Windows will be glazed already and 60kg each. Easy access at ground floor, no ladder needed. Need as well installation of glue on colonial bars/grille matching existing pattern.

Hi, I’m looking for a skilled professional with experience in glass cutting and window modifications. I have 15 studio rooms in Manly that each need a circular hole cut into an existing glass window to allow the hot-air exhaust hose of a portable air conditioner (approx. 2.5 kW) to be fitted safely and securely. Job Requirements: • Ability to safely cut a clean circular hole in glass (all rooms will require the same cut). • Install and secure the portable aircon vent hose once the units arrive. • Ensure the setup is safe, sealed, and stable so guests can’t tamper with it, the glass remains secure, and no outside air leaks in. • Provide your own tools and demonstrate relevant experience. Details: • Location: Manly • Rooms: 15 studio rooms • Task: Cut circular vent hole + install and secure exhaust vent • Timing: Flexible, but hoping to complete ASAP. If you’re experienced with glass cutting or glazing and have done similar work before, please get in touch with a quote and availability.

These are panels in windows There are five or six panels that need changing

The window glass is cracked and needs to be replaced.

Build a non-transparent glass doors or panel with handle for an open wardrobe with shelves. The design should be stylish and practical, without/with clear glass. I am open for new suggestions as well which will look good from your experience.

I need to replace broken glass panel for built in wardrobe. The frame still to be used.

Broken glass panel to be replaced. aluminium trimming. approx 33 by 46 cm

Need a glazier to make a small hole (60X80) on 3 windows to pass air conditioning pipes between indoor and outdoor units

The outside of my front door glass has a small hole caused by a stone. Inside is fine. Looking for a repair quote ASAP.

Need turn bulkhead to a grey water tank . So reinforce inside for grey water and make lid .

windows glass needs replacing

I need help repairing an Exo Terra glass frog tank that has a cracked/smashed panel in one bottom corner (see photo). I’m looking for someone who can: • Safely remove and replace the broken section • Ensure the tank is watertight and safe for frogs again Have your own tools and materials. I can get the glass if needed. I will drop it off if it’s too far for you to travel.

We need a glazier to measure and replace a cracked middle glass panel from in our living room facing the balcony. The middle panel is cracked but the other sliding window glass on the edges are fine. We are also keen to get a quote for replacement of the entire balcony access with sliding door. Glass dimensions 990 mm X 1200 mm

Window change second floor 3000x900mm

The current window consists of two glass panes with an opening in the middle, but the top pane has fallen down. Please replace it with either a fixed single-pane window (no ventilation) or a winder window that opens for ventilation. Replace with obscure glass, as the window provides visibility into a toilet.

I have 3 glass panels needing replacement - 1. Outside (Spa gone) - 1142mm W x 728mm H approx 2. Back of house - window marked with XXX - 800mm W x 740mm H approx 3. Upstairs bedroom - 648mm W x 633mm H Would like to get addressed ASAP - I suggest the glass measurements are double checked at or before fitting. Access is flexible.

Hi I need someone who knows how to cut glass to cut a 18cm round hole in a domestic pane of glass.

Glazier needed to replace sliding door clear glass.Also, door need to be take out. Two people required. size: 2180 X 1170 X 638

Window glass replacement app 1200x1400 ,

Small chip in fiberglass ice bath needs some filler or builders bog and touch up paint applied. Ive got the touch up paint which I can provide for you.