Find a local electronics repairer in South Moreton Bay

We need to replace 10 of our water damaged oval trestle tables which we use for indoor banquet functions at our venue. Oval Tabletops only, measurements are 1800mm x 1500mm. They need to be sealed (waterproof), light enough to be moved regularly from room to room by staff, yet sturdy enough for us to attach steel folding trestle legs. The tables can be constructed of whatever material you suggest as they will always be clothed with linen table cloths. Metal, foldable trestle table legs will be attached to the underside of each tabletop. If this is something you can assist us with, may I get a quote please? If possible, could you also advise the material and the approximate weight of each tabletop please? Thank you, Lina

I have Holden commodore 2010 Need to install sub amplifier reverse camera. I have all stuff.

Hi bula bites north lakes looking for handyman who can do benchtops at our restaurant we will take out the warmer as seen in the photos and replace with benchtops and might need 2 cabinets Please send me a quotation

My pup damaged the carpet on my stairs a bit and need replacement carpet on 2 steps for inspection

Quotes for someone to Cut down 2 thin trees, remove waste and the poison stumps

Hello I need someone to put wooden transition strip or rubber carpet transition strip for 4 bedroom, 2 bathroom doors ways guests room area. Very easy job but don’t have the time to do it.

3 hedge stumps from the front yard need to be ground, along with a grevillia stump from the backyard.

Have 3 walls that need a bit of a touch up/tidy for end of lease. Also Wood that’ll need a filler and sand and touch up on stairs

Hi need someone install sub amplifier reverse camera to my Holden commodore ve 2010.

Need 2 stumps dug up and removed.

Replace Vanity Taps I need someone to replace the taps on a standard bathroom vanity. I originally intended to replace the washer, but the spindle is too tight for me to unscrew. I have already purchased the new replacement taps, so the job is simply to remove the existing taps and install the new ones. Details: * Standard bathroom vanity * New taps already purchased * Existing taps need to be removed and replaced * Photos attached * Flexible with timing — anytime this week * Ideally looking for someone experienced with basic plumbing/tap replacement Thanks for your quote.

Repair roof flashing approximately 10 meters and coating touch up. I will provide coating material left from previous repair/painting. $350 + material cost

I need an 8 Gauge wire directly hardwired to the 12v + on the Sony Xplod Amplifier Circuit Board

My original task expired - Paul, please contact me to book. I have 1 x approx. 10cm across Yucca Stump and 4 x Other Clumped type stumps in a garden bed I need dug out.

Have some painting to be done, the edges are chipping, just needs touching up. There is one patch that will need bogging,

I'm looking for an experienced appliance repair technician or qualified electrician to diagnose a fault with my Blanco freestanding oven. The appliance has a gas cooktop and electric oven. The gas cooktop works perfectly, but the electric oven trips the mains/safety switch after running for a short time. We can reset the switch and restart the oven, but it trips again after heating up. I'm looking for someone to: Diagnose whether the fault is inside the oven (e.g. heating element, thermostat, wiring, etc.) or with the electrical supply. Advise what needs to be repaired. If it's a straightforward repair and parts aren't required, complete the repair on the spot if possible. Please bring the appropriate testing equipment and let me know your experience repairing Blanco ovens. Location: Murrumba Downs, QLD Budget: $120 (diagnosis only, with any repair or parts to be quoted separately).

Hi need a handyman at bula bites cafe north lakes who can fit benchtops and cabinet

Our taps are leaking and there is water underneath sink, we need to change our taps.

Please provide quote and availability. I've removed the old taps and shower head and cleaned off old silicon around them. I bought new valves, taps and shower head. Want to reseat tap seats and then install new valves, taps and shower head. Also seal up taps and head with silicon. The shower wall is ~5mm sheet and a hollow cavity behind, so not sure if need some sort of backing for the silicon.

The power circuit for the kitchen area keeps tripping at the switchboard. Even when all appliances are unplugged and nothing is being used, the safety switch/circuit breaker continues to trip randomly. Looking for a licensed electrician to inspect and diagnose the issue, identify the cause, and provide a quote for repair. Location: Bunya, QLD Please let me know your availability and estimated call-out fee.