Find local power point installers in Melbourne

1. Ceiling light: The light/fitting is not working properly , need inspect and repair it, or replace the fitting if necessary. 2. Double power point: The entire power point is broken and needs to be replaced 3. Ceiling light fitting: The light/fitting is coming loose and hanging down. Need safely re-secure it.

I have an old surface-mounted GPO that needs replacing. Two old rigid PVC conduits enter from above — the left is the incoming supply and the right continues to another working GPO. The downstream GPO needs to remain connected. Looking for supply and installation of a suitable 10A weatherproof surface-mounted GPO, with any conduit adjustment required for the installation. There is also an ceramic fuse that needs checking and replacing with the fuse wire. Please let me know your quote. Thanks.

Add a power point into backyard Brick wall there is powere poin directly opposite to where I want it on the inside

3 new indoor power points 1x living room 1x kitchen island 1x bathroom

Electrician - replace old outdoor power point and light with the same but new. See photos. I have already purchased the same style of power point and light.

Recessed power point in brick wall.

We need someone to replace power points

Install two dual power points in wall connecting to existing power supply in wall to power two speakers

Looking for a licensed electrician to install 4 new power points for kitchen appliances in a single storey house in Albert Park. Power points required for: • Oven • Cooktop • Rangehood • Dishwasher Please include labour and standard materials in your offer. I can provide photos of the existing kitchen and electrical setup. Timing is flexible, but ideally I’d like to have the work completed as soon as possible. Please only make an offer if you are a licensed electrician and can provide an electrical safety certificate upon completion. Thanks

Need some to provide and install an out door PowerPoint on a rendering wall . There is a near by indoor power point to work from .

I need installed 2 double Clipsal Weathershield single outdoor power points (GPO), there is one already installed 2 meters away, so you may be able to move that one and source power from there. Plus, Relocate a Pierlite BWP/T236EL IP65. It is a legacy 1200mm (4-foot) twin-tube IP65 weatherproof fluorescent batten one meter away. Check a fuse for a 3 phase switch that no longer seems to be working.

I need a licensed electrician to replace one existing double power point with a new USB-A & USB-C power point. I will supply the new power point. Straight replacement only — please see photo.

We want to put a power point in wall to mount tv

I live in an appartments. Looking for an electrician to install a new power point on my hallway wall. The other side of the wall is my bedroom, and there is already an existing power point on the bedroom side of the same wall. I’d like to add a new power point on the hallway side, ideally around the same location.

I’m looking for a licensed electrician to install one new double power point on a plasterboard wall in my apartment. There is an existing double power point approximately a few metres away near the marble shelf, which I’d like the new outlet to potentially be supplied from. The job: * Install 1 x standard double GPO underneath the existing picture frame (see photo). * Ideally run the cable inside the plasterboard wall cavity from the existing power point. * I want no visible cabling or plaster chasing between the two points. * Only the necessary cut-out for the new GPO. * Please assess whether the existing GPO/circuit is suitable for the additional outlet. * Supply and install the GPO. * Test and leave the installation compliant and tidy. * Licensed electrician only – Victorian electrical regulations apply. Budget: $250–$300 Seeking a fixed price agreed before starting. Please quote including labour, materials and installation and confirm you are a licensed electrician in Victoria. Photo attached showing the existing socket and proposed location

6 x gpo to be connected on newly installed skirting boards . Holes have been cut out.must be licensed electrician.cab be done today or tomorrow.

Looking for a licensed electrician to complete the electrical work required for a new heat-pump hot-water system being installed ( new double power point) Hot water system: Midea RSJ-23/300RDN7-L2 280L heat-pump hot-water system with electric element. Job details: • New Midea unit will replace the existing Aquamax gas hot-water system shown in the photos. • A suitable weatherproof outdoor Double power point/electrical connection is required for the new Midea unit. • There is already an external power point supplying the ducted heating approximately 2–3 metres away. • Good access underneath the house via the subfloor. • Photo of the existing switchboard is attached. • Electrician to determine whether an existing circuit can safely and compliantly be used/extended, or whether a new dedicated circuit/RCBO is required for this particular Midea unit. Please quote your best ALL-INCLUSIVE price for everything electrically required to have the Midea ready for connection, including labour, weatherproof power point, cabling, circuit/RCBO if required, materials and electrical compliance/safety certificate. Please base your offer on the information and photos provided and advise in your offer exactly what is included. Must be completed by a licensed electrician and fully compliant. Thankyou 😊👍

Installation of a double power point in place of existing single power point and install additional double power point in kitchen. Walls are brick and plaster.

Help me replace 2 LED light bulb, power point button, and drawer slider in apartment

Top story one bedroom apartment, pitched roof with man hole located in ceiling, plug needs to be installed in a cupboard to connect a tv