Find a local Tasker to replace your engine in NSW

Hi, I need a qualified person change the engine oil and filters on my car. Location: I can drive to your place/anywhere you suggest. Parts: I already have the engine oil and air/oil filter. You will only need to supply the labor and your own tools (jack, axle stands/ramps, oil drain pan, filter wrench). Vehicle Details: 2014/15 VW Passat Sedan 1.8tsi Requirements: Clean and tidy job Safe disposal of used oil and filter Check of fluid levels after the change. Please let me know your availability when submitting an offer.

Looking for a mechanic or experienced home mechanic to test and remove a 5S-FE 2.2L engine from a 1998 Toyota Celica located in Ingleburn. The motor is currently still installed in the car and running.  Requirements: 1. Pre-Removal Testing: Before unbolting anything, start and run the engine, perform a quick compression test across all 4 cylinders, and check for any unusual noises, smoke, or milky oil/coolant.  2. Engine Pull: Carefully remove the bare engine long block using an engine crane.  3. Equipment: You will need to bring your own engine crane, compression tester, and standard mechanic hand tools/sockets.  Location: Ingleburn, NSW Date/Time: Flexible depending on seller availability.

Changing self-buy engine oil, filters, 4 braking pads ,rotors parts (Yr 2018 Peugeot 5008 1.6T petrol, 73000km)

Looking for an experienced auto electrician or vehicle electronics installer to supply and install a keyless entry and remote engine start system on my 2017 Volkswagen Golf GTI MK7.5 (automatic, push-button start).

I have a 2017 Mercedes-Benz C350e Plug-in Hybrid with a Check Engine Light. A professional Autel diagnostic scanner detected: P0840 – Transmission Fluid Pressure Sensor/Switch “A” Circuit Status: Current, Pending & Permanent I am looking for an experienced Mercedes-Benz mechanic / transmission specialist, preferably someone familiar with the C350e hybrid transmission, to properly diagnose the cause and repair it.

Need mechanic. Water is coming out from one of the pipes near the engine

Hi, I’m looking for a mechanic or auto electrician to diagnose and repair a Check Engine light on my 2011 Hyundai i45 2.4L. I scanned the car with an OBD2 scanner and the only fault code showing is P0138 – O2 Sensor Circuit High Voltage (Bank 1 Sensor 2). The code is showing as both stored and pending. The car is still running normally and the Check Engine light is solid, not flashing. I’m looking for someone who can properly diagnose the cause before replacing any parts. I would like the downstream O2 sensor (Bank 1 Sensor 2), wiring/connectors and circuit checked to determine whether the problem is the sensor itself or an electrical/wiring issue. If the O2 sensor is confirmed faulty, I’m happy to have it replaced. Please let me know your price for diagnosis and, if possible, an approximate price for repair/replacement depending on what is found. Located in Campsie, NSW. I can go to your place if needed

Engine oil dipping issue on 2007 Toyota Corolla

Remove an engine from a car

Holden ve commodore sv6 engine and transmission removal from car. Front end is already off and is on jack stands. Will require tools and engine hoist

Title: Mobile Mechanic: Diagnose & Fix Engine Oil Leak on 1999 Toyota Landcruiser Task Description:Looking for a qualified or experienced mobile mechanic to look at an engine oil leak on my 1999 Toyota Landcruiser. Vehicle Details: 1999 Toyota Landcruiser (100 Series / 70 Series)The Issue: There is an active engine oil leak coming from the front area of the engine. It is leaving oil spots under the car. I need someone to clean down the area, accurately locate where the leak is originating (e.g., front main crankshaft seal, oil pan, or timing/valve cover), and complete the repair.

Vehicle: 2006 Ford BF Fairmont MkII (NA Barra) Task: Basic engine-health upgrade & parts replacement Parts Supplied (all fluids provided + pans etc): • Aluminum radiator • New expansion tank • Silicone coolant hoses • Solid band ring clamps • Thermostat + gasket • Proflow trans cooler (braided lines) • Aeroflow Alternator & replacement plug • Drive belt • 2x cam sensors • Upgraded power steering line • Red/black OFC cables for overlay, copper lugs & fuse holder • SAAS throttle controller Note: I can remove front bumper before you arrive so you can avoid bodywork. Please have: • Trans fluid pump & OBD2 scanner for ZF temp check • Soldering iron (alternator plug) & hydraulic wire crimpers (lugs) I will provide the complete parts list & project brief via text once assigned. Please confirm your experience with the Barra platform and BA/BF chassis when offering. Cheers.

Stainless bolts stuck in block. Would like removed and new ones inserted. There is enough room to move around. Old Mercury 200Hp motor

I need someone to remove a motor from a Daihatsu Delta tipper 2005, so I can take it to my engine reconditioner, work is preferred to be done on site at Carlingford.

Need to fix coolant leave or fix smoke coming out of front of the engine bay before 12 pm today

Wanting to take out an engine from a donor car Toyota crown 2012 v8 in Glenbrook

Require engineer to check my trailer design (SOLIDWORKS) complete an FEA simulation and provide results that will satisfy my R.O.V.E.R submission. Trailer will be submitted as a 5000mmx2300mm (not including draw bar)PIG Trailer. And has been fabricated in line with current VSB1 Vol6 & Australian Design Rules (ADR), using structural Australian steel. All required (as per ADR) parts and fittings are new with Component Type Approvals. Tandem Electric brakes, tyres, rims and suspension are rated to 3.5+ ton. Chassis is 95% complete. Currently finalising fabricating draw bar. Will run all the way to front suspension hangers and protrude approx 2000mm from front chassis rail.

A bolt has broken off from a side mounting bracket into my engine. I want to get it drilled out and preferably without removing the bracket or dropping the engine. Let me know what’s possible, cheers

Need Engine mounts changed in a 1997 Toyota Hiace 1kz TD RWD Please add quotes for labour only Located closer to Forestville the better

I have a landcruiser 100 series with petrol engine 2uz-fe. I have timing belt kit already and need someone with experience to replace this timing belt