Find an experienced driveway repair contractor in South East Melbourne

Looking to prepare and repaint driveway, aprox 22sqm. Looking for site inspection to provide quote and discuss options

Hi, I need a small rectangular section of my concrete driveway prepped, reinforced, and poured to match the existing slabs. You can see the exact area in the attached photos. It has filled with mud and weeds over time, which will need to be cleared out first. ​Scope of Work: ​Excavation & Prep: Dig out the mud/weeds/soil to approximately 150mm depth to allow for a proper compacted road base (50mm) and concrete slab (100mm thick to handle vehicle weight). ​Formwork & Doweling: Supply and install a straight timber form along the left garden edge. Drill into the existing concrete slabs on the right/ends and insert steel starter bars/dowels to tie the new patch to the old driveway (preventing independent shifting/cracking). ​Reinforcement: Supply and place steel mesh (SL72 or equivalent) on plastic chairs. ​Pour & Finish: Supply and pour standard strength concrete (minimum 25 MPa). Screed it level with the surrounding driveway slabs and finish with a light broom texture to match the existing non-slip surface. ​Clean up: Take away any dug-out soil and leftover debris. ​Materials: Tasker to supply all materials (crushed rock base, timber form, steel mesh, dowels, and concrete bags/mixer). ​Please specify in your offer if you have experience with concrete patching and can bring your own tools/mixer. Flexible with dates. Thanks!

Won’t take long. Just need a very long ladder. Need 2 weep holes completely waterproof sealed and a small section off a suspended drive way sealed. These areas have caused water ingress into home

I am purchasing a custom automated sliding gate kit (5m and 3.3m spans). I need an experienced tradie to come out with a laser level/string line, check the level across the driveways and fence line and give me the exact millimeter measurements to send to the fabrication factory. Must understand sliding gate clearances/tails.

Pour conrete for a new build home

Saw-cut and remove damaged concrete section of driveway, drill and epoxy-dowel into the existing slab for load transfer, and repour with high-strength concrete. Repair must be suitable for vehicular traffic. Photos show damaged area from different angles. Damaged area is approx 2 meters (L) x 15cms (W) x 6cm (D). We can arrange for the road to be closed while work completed and manage traffic whilst it sets. Additional photos and analysis of previous failed compound repair added. The cause according to this report is a cold join that overlaps. We want to ensure that the solution will resolve the underlying cause. Please consider this info and revise your quote if needed. Thank you for your time.

Timber fencing and concrete driveway

I am looking for someone with experience in earthworks and access to suitable machinery to help prepare access to my home-based dog grooming salon. The property currently has a steep, muddy slope with no existing pathway. The job includes: Excavating and levelling a pathway from the driveway to the salon entrance Levelling and improving sections of the driveway Creating a safe and practical access route for customers and their dogs Cutting out and preparing the pathway area for weed mat and rock installation (weed mat and rocks will be supplied and installed separately) General site tidy-up of disturbed areas The property is located in Cockatoo, VIC. Please let me know: What machinery you will use I have included a photo of the pathway I am after. I will need the wood beams installed but not the gravel. Photos can be provided, and site inspections are welcome before quoting. Completion before 12 June highly preferred as access is required for a home-based business opening

I need quotes to wash and seal my 25meter driveway

New side gate 1, approx 730mm, would like some light frame with prestained marbau or something similar with sliding bolt to lock New side gate 2, approx 1130. Again would like something similar to gate 1. Neighbour’s driveway gate, needs to be attached to new fence but old fence was falling over, will need realignment.

Need to put two cameras in. My driveway Cheapest basic ones

need a quote for the strip along the fence on the left & the lawn from driveway to stones on the right where grey car is so extending the width of the driveway to park 2 cars

I want to move the council water tap to 600mm. The council has installed a closed fixture near the garage driveway,

Paint the driveway. Area about 100 square meters

Pressure wash the driveway, let it dry and then roll sealant over pavers. We will provide all tools and sealant.

The purpose of this project is to install new concrete around the perimeter of the house and extend the existing driveway to improve accessibility, durability, and overall appearance of the property. A. House Perimeter Concrete • Supply and install concrete around the full/partial perimeter of the house. • Area to be properly excavated and leveled before installation. • Install compacted crushed rock base for stability. • Provide formwork to shape and support the concrete. • Concrete thickness: approximately 75mm–100mm (as required). • Finish: smooth / broom finish (non-slip). • Ensure proper slope away from the house for water drainage. B. Driveway Extension • Extend existing driveway to [left] side as required. • Excavation and site preparation including removal of soil/debris. • Install compacted sub-base (crushed rock). • Lay reinforcement mesh (if required). • Pour and finish concrete to match existing driveway level and style. • Concrete thickness: approximately 100mm–125mm for vehicle load. • Finish: broom finish

Trim trees along side of driveway Type of gardening: Other Size of garden: 50m²-150m² Has green waste bin: Yes

crack on epoxy driveway and water oozing from the crack once we receive rain no pipe leakage or drainage leak inspection done by insurance company expert every think tested the length of crack is 5 meters. i also interested to get a quotation for new epoxy paint on top of existing one

Looking for an experienced fabricator / welder / gate specialist to increase the height of my existing front driveway gate. The gate is a motorised double swing gate with vertical slats (powder-coated black). I want to raise the height so it sits just below the hedge line for added security. Scope of work: • Supply and install a top extension to the existing gate • Match the existing vertical slat design and spacing • Ensure the extension is structurally secure and aligned • Maintain smooth operation of the existing motorised swing mechanism • Finish to match existing (black powder-coated look) Please include: • Photos of similar work (if available) • Your recommended approach Happy to discuss ideas, just want the cleanest and most cost-effective solution. Photo 2 is existing and Photo 1 is proposed.

Remove two concrete slabs with cracks through them (pictured) and replace with new concrete slabs. We may also consider removing the third concrete slab (depending on timing/cost of the first two). |Please only quote for removing and replacing the first TWO slabs. The measurements of the broken concrete slabs are provided below (approximate): First & second slabs: 1) & 3) 5.7m 2 & 4) 2.86m Third slab: 5) 3.5m 6) 5m 7) 3.6m Flexible as to timing. We are in Beaconsfield Upper (3808).