Find an experienced chair repair pro in Brisbane Bayside

Spraying everything, including the table, will give a more uniform finish across the set — good call. Here's the final version: **Sand & spray paint dining set — 4 bentwood chairs, 4 stools, 1 round table** I have a matching dining set — 4 bentwood chairs, a round pedestal table, and 4 kitchen stools — that all need a full sand back and repaint in white. Current paint is worn, scuffed, and inconsistent across the pieces. **Scope of work:** - Full sand of all 9 pieces (chairs, table, stools) to prep for repainting - Fill any chips or dents as needed - Apply primer - Two coats of white paint, spray-applied across all pieces for a smooth, even, professional finish - Extra care needed on chair/stool spindles and turned legs **Details:** - 4x bentwood-style dining chairs (curved backs, turned legs) - 1x round pedestal dining table with glass top insert - 4x simple timber stools - Can be worked on at my place, or happy to help load into a vehicle if you'd prefer to take them off-site (useful if spraying needs a proper setup) - **Paint and Zinsser primer will be supplied — please bring your own sandpaper, spray gun/equipment and other tools** - Looking for a clean, smooth, professional finish across all pieces — not a rush job **Budget:** $350 (negotiable for the right person with the right skills) **Timing:** Flexible, but ideally within the next few weeks. Happy to share more photos or answer questions.

Build three simple flat packs - a chair, desk, entertainment unit

Chairs to be assembled happy to pay 50 dollars

No longer working. We have 2 of the same controller (2nd from warranty replacement). LCD still works, power on by main switch only. Some buttons are inconsistent depending on the context. However, "OK" and "Power on/off" buttons no longer work. The chair is useless without this controller.

Chair keeps lowering by itself

Chair not working buttons not on chair

I need 3 wooden chairs fixed, they are shaky and unstable they need to be glued or drilled.

Mechanism on side of recliner has broken

My wheelchair ramp is made from a timber frame covered with a sheet of marine ply. It needs to be raised by about 10cm at the door .

I’m looking to get a small job done BEFORE Sat 13th. We have an outdoor area that needs to be paved. Apologies for the drawing, but it will give you a rough idea of measurements and if it’s a job you would like to quote/ have time for. We would like to pave with this Tuscan stone that’s 30mm thick. At the moment, the ground has been stripped of grass but dirt will need to be evened out. Pavers have been sealed on the topside and edges. We were planning to do it ourselves with a road base and sand foundation but don't have the time. (Will need to bring base materials - roadbase and sand) As for the chair, we wanted an L-shaped chair framed with wood and concrete sheets then rendered with a smooth finish. Inspiration photos are below. (Will need to bring all material for this haven't sourced it yet) Lastly, we will need a drain dug in (already sourced). There is a downpipe you can tap into on the wall side of the pergola. Really not sure how much these things cost so sorry if the budget price is off! Thank you!

Electric chair broken needs fixed

I have 4 wooden chairs that need fixing. They need screws and glue I think as shaky when sat on. - Due date: Flexible

Repair 2 x wicker chairs

My recliner is an older chair and has a manual mechanism that does not work anymore. The footrest has broken off the frame and the mechanism under the chair no longer works properly.

Old recliner needs manual mechanism and footrest and handle repaired

3 x dining chairs needs repair. The ratten section has broken and needs fixing. We don’t have extra ratten and will need this to be provided too. Thank you :)

Remote sometimes works sometimes not. If you fiddle with the connection behind the seat it will sometimes work again

Need someone to build a sit to stand desk and chair from Temple and Webster

Leg is loose at the back and needs tightening

The job has been done previously but needs a further resand so I can varnish. Solid wood table and 2 x pew type chairs.