Find a local car lighting installation service in Sydney Eastern Suburbs

Fill in a short form and get quotes from professional LED light installation service


Excellent rating - 4.5/5 (9200+ reviews)

When you want to install led lights on your car

  • Car ambient lighting installation
  • Car lighting installation
  • LED headlights installation
  • Underglow installation
  • Rock light installation
  • … or anything else
It only takes 2 minutes. And it's free.
Up to 50% cheaper than franchise dealers
No job too big or small
Free insurance coverage
Secure cashless payments
Same day or next day service at no extra cost

Best rated LED lights installers near me

What is Airtasker?

Post your task

Post your task

Tell us what you need, it's FREE to post.

Review offers

Review offers

Get offers from trusted Taskers and view profiles.

Get it done

Get it done

Choose the right person for your task and get it done.

Now Available
  • Get it done now. Pay later.
  • Repay in 4 fortnightly instalments
  • No interest
  • Available on payments up to $1,500

Suggested reads about LED Lights Installation

  • How much does it cost to replace an alternator?

    Read more

What do LED Lights Installation services include?

The LED lights installation service includes cutting the right-sized LED light strip if necessary, sticking and mounting the strips, bars or headlamps onto your car, connecting the lights and its control panel or control switch to the power source. The service may include other incidental tasks for installation like cleaning the surfaces for mounting.

Preparing lights for mounting

Your auto electrician or sparky cuts a length of LED lights that will fit onto your car or SUV. For some car or SUV models, they may temporarily remove your car or SUV’s dash trim panel for easier access to the mounting spot. They may also remove the glove compartment to measure and prep for mounting at the passenger’s side. Your electrician cuts the right length of LED light strip or uses the appropriate length of prefabricated LED light tubes.

Cleaning surfaces

Before installing any of the LED light strips or tubes, your installer can clean the surfaces where the strips will be stuck onto with rubbing alcohol. This will ensure stronger adhesion as dirt, grease or grime can interfere with the effectiveness of the adhesive used to mount the LED light tubes or strips. Once cleaned, your auto electrician allows the surfaces to dry for about a minute before proceeding to the next step.

Mounting the LED lighting system

After the surfaces where the LED light tubes or strips and the control panel or switch are cleaned, auto electricians then attach these to the prepared surfaces. Depending on their type, your electrician can use industrial-strength adhesives or zip ties to mount them. The lighting system’s control panel or switch is then glued to a spot on the centre console trim, at the driver’s side. Taskers can reattach the glove compartment and dash trim panel after mounting.

Connecting to the power source

Once the LED light tubes or strips and the control panel are attached, Taskers can proceed to connect them to the power source. Depending on the way the LED lighting works, Taskers can connect these to your car’s battery, cigarette lighter or fuse box.

For this step, Taskers do wiring work like wire-stripping, splicing and soldering. Taskers ensure that the lighting system gets the right amount of power and doesn’t interfere with the starter motor or affect other car electronics.  

Connecting LED headlamps

Auto electricians that do LED headlamp installation can perform all the tasks required to upgrade your car’s headlamps. This includes removing your car’s old halogen headlamp bulbs, cleaning the contact points, installing the new LED headlamp bulbs, and doing the necessary cleaning of the headlamps to increase clarity. Auto electricians can also do the needed wire-stripping, soldering and splicing to connect the new LED headlamps to the car’s battery.

Recent LED Lights Installation tasks in Sydney Eastern Suburbs

Led lights installation


Maroubra NSW, Australia

24th May 2021

Hi guys, I am about to preaches some good quality led lights for the interior of my golf gti. With this job inside door panels need to come off to do proper neat wiring. Job will involves splicing and tapping into powering also taking of door trims ect to get to the right places Looking at doing front and rear. If you interested in taking this job up I habe a references video to see to give you guidance and understand so please shoot me a message if willing to take it on. Kind regards j

I need LED lights installation


Bondi Beach NSW, Australia

29th Dec 2020

Kings spotlights with plug and play wiring harness installed to a 2017 VW amarok



Bondi Beach NSW 2026, Australia

18th Nov 2020

Need someone to bring me these EXACT lights. Will buy up to 5. Price will vary depending on quantity able to be acquired.

Wiring LED lights to a battery


Dover Heights NSW, Australia

11th May 2019

Is for a uni project. Need help tomorrow Sunday only. A quick job if you know what to do. We may need to discuss what components are needed. May need to come at 9am & then later after 5 if extra components need to be bought.

Sultan ali Z. gave his all to help resolve the wiring issues for a prototype. He seemed to like the challenge of this one-off problem although is equally content in assembling repetitive items. He was patient and resourceful and asked the right questions to meet the technical and aesthetic requirements of the brief. He was prepared to take whatever time was necessary to complete the job for the tight deadline. His calm demeanour was much appreciated. We would definitely use him again and take him up on the offer to do an even better job next time, with more forward planning to reach an optimal solution.