Hire a trusted shelf hanging expert in QLD

I need the shelf hung onto the wall please. Ideally a renter friendly option would be great but understandable if it can’t be.

Installation of floating shelf in bathroom

install wall shelf system 4 rows need to be secured to wall studs. Tools required, Drill, Level

Need 4 long shelves installed in garage approx 16ml thick x 1.5M long and 2 small shelves installed in small laundry cupboard.

Two small shelves installed Today if possible

I need an Airtasker to change a washer in the bathroom, install 2 x shelves in the kitchen, tighten spa crews & remove some silicon from the internal area of the spa

Install 2 x shelves. The shelves came with 2 wooden brackets to mount on the wall however would prefer them to be floating if that’s possible. I have provided a photo of where the shelves would go

Install shelf, I have the shelf and brackets . Just need masonry screws Need to re install the bracket there and patch holes where I tried if visible outside the bracket

Need a shelf installed in my kitchen. It was previously mounted on the same wall and is going up in a new spot. The wall is a Besser block behind a gyprock cover, so it will need appropriate anchors for both surfaces. Shelf and brackets supplied — you'll just need your own tools and fixings.

I'm looking for someone with experience mounting items securely to walls. I need the following installed: Hang 1 shelf in the laundry. Install 1 wall-mounted bike rack/holder in the garage. Install 1 wall-mounted motorbike helmet holder in the garage. Install 8 wall-mounted cat steps on a bedroom wall. The cat steps will need to be installed securely into wall studs or with appropriate anchors, depending on the wall type, to safely support my cat. Please bring your own tools and let me know if I need to provide any additional fixings. When responding, please include: Your experience with similar installation jobs. Your availability. Your quote for the complete job. Thanks!

Acoustic panel cut and installed, TV mounted over it (65” TV), soundbar mounted under the TV and a floating shelf installed above the TV.

Hang shelf into tiled wall

install: • 3 full-width shelves. • 1 vertical support panel to create 2 equal sections below. • The top storage area must remain completely open • Cabinet width: approximately 2250mm. • Cabinet depth: approximately 460mm. • Lower shelves divided into 2 equal bays • White melamine board preferred. • Shelves must be adequately supported to prevent sagging under normal storage loads. Also, on the top of the side of garage wall, install 5 meters panel in one side and 2+2 meters panel on the other side (install same as shown in the photo)

Need some shelves installed in an unused cupboard. At least 3 shelves.

Secure gun safe to concrete floor. ( Drill 6-14mm holes in concrete and secure safe with dynabolts) Attach 3 shelf brackets to plasterboard wall.

I have all the parts for a shelf that use to be in our walk in closet. We removed it and now want it installed in our garage to free up some space. Shelf is about 180cm length, with 4 triangle wood supports. The wall is drywall. Hardware will be required.

Attempted install of shelves into studs but screws have snapped head off on two. Removal of broken screws, re-install of screws into studs and hanging of shelves off screw.

I have a 600x235 shelf kit from Bunnings that I need installing in my laundry room for the NBN installation. I am available today (14 May) Monday, Tuesday (18/19 May) or Wednesday 20 May before 1:00pm.

Install 3-phase reference wiring + Shelly energy monitors in switchboard (licensed electrician) Scope: - Install 1 × 3-pole DIN MCB (metering/reference circuit) - Install 5 × Shelly 3EM-63W Gen3 units inside switchboard - Provide clean L1 / L2 / L3 voltage reference distribution to all Shellys - Connect: - Neutral to neutral bar - Earth to earth bar - Install and route CT clamps (3 per device = 15 total) on nominated circuits - Neatly terminate, label, and secure all wiring - Test and verify correct operation (phase alignment and readings) Requirements: - 3-phase switchboard (Hager gear) - Must be fully compliant (AS/NZS 3000) - No double-lugging of breaker terminals - Preference for clean, scalable solution (e.g. terminal blocks or equivalent) Notes: - All Shelly devices supplied - Switchboard has available DIN space - Looking for a neat, professional install — not a quick patch job Please include: - Confirmation of licence - Approach you’d take (brief) - Availability Location: Kenmore

I am looking for a handyman experienced in: - hanging one mirror - would need to bring necessary drill bits - hanging 2-3 light canvas artworks - hanging and moving 2 tvs (brackets already installed in the wall) - provide and install white single shelf to place Bluetooth bar speaker under TV