Find a local electric car service expert in VIC

Harley sportster was draining battery. Had to trickle charge every time . Now it wont even jump start . And makes fast clicking sound

My caravan is about to be sold. Indicators and brakes only work when plugged in to car with 7-pin flat AND Anderson plug. Buyer only has 7-pin flat. Apparently the earth connection on 7-pin on caravan side not working. Need multimeter and those types of skills.

I have a electric quad bike I need serviced and to get it running again stopped when it said safe before service

King wolf gt pro e scooter back brake bleed

I anticipate this task might take a whole day. I would assume here would be one additional visit to org side that day of work, Hope you can help!! Looking for a licensed electrician with campervan/caravan experience to complete the electrical fit-out in my 2020 LDV Deliver 9 LWB campervan. Most components are already purchased and ready to install/connect: • 2 × 200Ah lithium batteries (400Ah total) • 40A MPPT solar controller • 40A DC-DC charger • 40A mains battery charger • Battery monitor/shunt • 2000W pure sine-wave inverter • Solar panels to be mounted on existing roof racks Looking to have the system wired and set up for solar charging, alternator charging, shore-power charging and 240V power when off-grid. I may replace the existing inverter with a 2000W inverter with automatic mains/shore-power transfer and would appreciate advice on this before purchasing. The van interior is currently unfinished, so access for installation and wiring is easy. Electrical certification is required on Completion

Need tunning 2 hoist, tyre changer and wheel balancer connection, air compressor , 2 led roof lights installation, single phase electricity 15 amp connections required $1500 is my limit Thank you

My jeep won’t start and it’s something electrical

Experience required with cutting, crimping and pin out of ECU. Need sound knowledge of vehicle electrical systems and devices such as Relays, fuses and Power Control Modules. I can offer longer term work if you are the right person for the job.

A big thank you to anybody that responds this may be a good job for somebody local to Cranbourne that knows how a multimeter & test light works 2000w controller 2000w motor 42v battery The wires came undone And dont know the order to put them in I need help !!

Looking for an experienced installer to fit an electric (motorised) roller tonneau cover to my BYD Shark 6 ute. - I have the cover and all parts, still boxed. - The job: fit the rails and canister to the tub, wire the motor to 12V power (fused, tidy loom), run the drain tubes, and test the remote/switch. - Please say whether you've fitted electric roller covers before (BYD Shark experience is a bonus) and whether the tub needs drilling. Location: you can come to me in Clayton South or Moorabbin, or I can drop the car at your workshop nearby. Timing: flexible, within the next 2 weeks.

Looking for a sunny to help out on a new build rough in

Needing a qualified and insured electrician to pop over and connect a new truck tail lift two button pendant controller to my Hino 300 truck. I'm being told it's "plug and play" but can't get it to work, Ive also been told it needs an electrician- I need help please. We are replacing a damaged one, the new one is not plig and play and needs to be connected. I have 2 x controllers I'd like connected I'd we can please.

12V Canopy Electrical System Installation – Nissan Navara I’m looking for an experienced 12V auto electrician to install and neatly wire a complete 12V/240V electrical setup in the canopy of my 2018 Nissan Navara NP300 ST. The main electrical system will be mounted on a board on the passenger side of the canopy, closest to the vehicle. I’ll be boxing/enclosing the electrical area once completed. Main equipment includes: * 230Ah LiFePO4 battery * 40A DC-DC charger with MPPT * 2000W pure sine wave 12V–240V inverter * Battery/inverter remote displays * Main fuses and fuse holders * Anderson connection * 12V accessories Work required: * Securely mount all electrical components to a neat backing board * Install and terminate appropriate battery, DC-DC and inverter cabling * Install main fusing and isolation/protection * Wire a 12V fuse/switch panel * Install multiple 12V cigarette/merit sockets * Install 240V GPOs supplied from the inverter * Run and secure all cabling neatly throughout the canopy * Properly earth/ground where required * Label cables, fuses and switches * Ensure all connections are properly crimped, insulated and protected * Test the complete system and verify everything is operating correctly I want the finished installation to be very neat, professional and easy to service, with sensible cable routing and no loose/unprotected wiring. The fridge will sit next to the electrical section, with a bench/drawer setup occupying the remaining canopy space. Important: I already have the main equipment. I’m primarily looking for professional installation, wiring, termination, protection and testing. Please only apply if you have experience with high-current 12V systems, lithium batteries, DC-DC chargers and 12V/240V inverters

The car doesn't wanna start, there is no spark in the spark plugs. I believe is an electrical problem.

My Electric scooter tyre is flat. Can anyone help me fix it or replace the tyre if needed.

I have a few things that wired such as dual battery, spotlights, uhf and inverter. Price is for a quote

Lamp has been working if I jiggled the cord but now it’s stopped working at all.

I'm looking for a mobile auto electrician or mechanic with BMW/European vehicle experience to diagnose an electric tailgate fault on my 2017 BMW 4 Series F36 Gran Coupe in Newtown, Geelong. Symptoms and previous diagnostic history: - The boot can be opened manually, but powered opening/closing has stopped working. - Pressing the close button produces a click but no powered movement. - A previous BimmerLink scan recorded HKFM fault 801712, right tailgate spindle drive interruption. Faults were cleared during earlier troubleshooting, so please check the current fault status and physically test the circuit. A replacement right-hand tailgate motor/spindle may be needed, but I want the fault confirmed before buying any parts. I cannot access the motor myself to check its label or connections. The task is to: - Diagnose the fault using a BMW-compatible scanner and physical electrical checks. - Inspect and test the right-hand spindle wiring and electrical connector for damage or a broken connection before recommending replacement. - Check the motor, latch and power supply as needed. - Photograph the existing part number and connectors if replacement is required. - Advise on the repair and quote separately for fitting any replacement parts. Please include your BMW experience, diagnostic equipment and total call-out/diagnosis fee in your offer. Diagnosis only at this stage. Any extra diagnostic time, repairs or parts purchases must be agreed separately.

I need help wiring a 12v setup for my van and also help figuring out what other little parts i may need to buy

UVUE dash cam was removed from previous car. Needs to be re-installed in new car. Front & back cameras. Experienced Auto electricians only.