Light Bar Installation Jobs in Sydney Northern Beaches

Browse through over 500 Light Bar Installation Jobs.

See what you could earn

$0

per month

Based on average light bar installation task prices. Actual marketplace earnings may vary

Why join Airtasker

Join Airtasker

Light Bar Installation tasks in Sydney Northern Beaches

Check out what tasks people want done near you right now...

I’m replacing old locks/levers on 3 internal doors with new Gainsborough Matte Black Choice Harper Square Privacy Lever Sets (60mm backset, 54mm bore, 25mm edge bore — I’ll supply the handles, latches and instructions). The old hardware has already been removed. Scope: 1. Patch 2 door edges: two doors had mortice locks, leaving rectangular cavities in the door edges. These need solid timber infill blocks, glued and packed tight, planed/sanded flush — the new 25mm latch bore and faceplate screws go straight through the patched area, so it must be solid. Please bring suitable timber and adhesive. • Door 1 (bathroom): cavity approx. 100mm high x 17.5mm wide, door thickness 34.8mm • Door 2 (second bathroom): cavity approx. 57mm high x 16mm wide, door thickness 34mm • Please verify cavity depth on site — I haven’t measured it 2. Drill new holes in all 3 doors: 54mm face bore at 60mm backset + 25mm edge bore. Third door (bedroom, 34mm thick) has no cavity — drill and fit only. Note: all 3 doors have existing old spindle holes (~14–23mm) that overlap the new bore centre, so a hole saw pilot bit won’t have material to engage. You’ll need to clamp a sacrificial board over the face to guide the hole saw, or use a lock installation jig. The old holes fall entirely within the new 54mm bore and will be drilled away. 3. Install the 3 lever sets including latches and strike plates, chiselling strike plate recesses in the jambs as needed, and confirm doors latch and the privacy function works. Doors can stay on their hinges. Painting/finishing not required. You’ll need a 54mm hole saw, 25mm spade/auger bit and chisels.

Brookvale NSW 2100, Australia

Sun Aug 23 2026

about 1 hour ago

Open

Install 2 outdoor GPOS (supplied) 1 x 20amp ( pictured) 1x15 Amp Run cable from mains ( marked yellow to the brick wall also marked yellow) There is a conduit under the concrete path marked blue Power points will be supplied, you’ll need to supply cable. Approx distance from mains to gpo location is 8m

Belrose NSW 2085, Australia

Sun Aug 23 2026

about 6 hours ago

Open

I need a professional to weld 2 parts on the trailer so I can install the stabiliser legs. Please check photos. Location is Killara 2071.

Killara NSW 2071, Australia

Sat Aug 22 2026

about 9 hours ago

Open

Location: Kellyville Currently timber fencing and needs replacement Need to install Colorbond fencing 1.8m height and concrete sleepers (75 mm) Rear (15.8 m) - need 75 mm concrete sleepers based retaining wall (24 of them / 60 mm retaining wall for the stretch) RHS (25.5 m) - need 75 mm concrete sleepers (26 of them / 40 mm retaining wall for the stretch). LHS (33 m) - need 50 mm concrete sleepers (12 of them / 20 mm height) 2 x side gates Old fence to be removed Rear and RHS - Ag pipe, blue metal, geo fabric

Sat Aug 22 2026

about 11 hours ago

Open

Currently timber fencing and needs replacement Need to install Colorbond fencing 1.8m height and concrete sleepers (75 mm) Length: 33 m (1 sleeper), 15.8 m (3 sleepers), 25.5 m (2 sleepers) 2 x side gates Old fence to be removed

Sat Aug 22 2026

about 11 hours ago

Open

Repair cracked shower tile and reseal shower Looking for an experienced tiler/bathroom repairer to repair a cracked floor tile at the edge of an existing shower and reseal the shower area. As shown in the photos, the floor tile immediately adjacent to/under the shower screen frame has cracked. Access to properly remove and replace the tile may require temporary removal of part of the aluminium shower screen/door frame. Scope of work: * Inspect the cracked tile and surrounding shower area and confirm the appropriate repair method. * Carefully remove the cracked floor tile without damaging surrounding tiles. * Temporarily remove and reinstall the shower screen/door frame where required to access the tile. * Check the substrate beneath the cracked tile for any obvious damage or movement and advise if further repairs are required. * Supply and install a suitable replacement tile. Ideally match the existing grey tile as closely as reasonably possible. * Re-grout the repaired area to match the existing grout. * Remove deteriorated/failed silicone and sealant around the shower perimeter, screen/frame and other relevant junctions. * Thoroughly clean and prepare surfaces before resealing. * Apply new high-quality mould-resistant sanitary/bathroom silicone to provide a neat, watertight finish. * Reinstall and correctly seal the shower screen/frame if removed. * Clean up and remove all waste on completion. The intention is to properly repair the cracked tile and restore the waterproof seal around the shower, rather than simply filling or sealing over the existing crack. Please include labour and indicate whether your quote includes the replacement tile, grout, silicone and other materials. Photos attached showing the cracked tile and shower frame.

Manly NSW 2095, Australia

Sat Aug 22 2026

about 11 hours ago

Open

Install new electrical Richmond sliding gate motor from Bunnings to replace old gate motor please provide an offer to complete the job. Thanks

Manly NSW 2095, Australia

Sat Aug 22 2026

about 12 hours ago

Open

Looking for a licensed electrician to complete the following work at my house: - Install 2 new ceiling fans where existing lights are currently installed - Install or replace 4-5 new ceiling lights - Install approximately 3-5 new downlights - Tidy and organise existing electrical wiring and cables Please provide: - Your electrical licence details - Your availability, preferably next week Photos can be provided, and a site inspection can be arranged if required.

Pymble NSW 2073, Australia

Sat Aug 22 2026

about 13 hours ago

Open

Supply and install tap to water tank and inspect pump to make sure its operating ok

Sat Aug 22 2026

about 19 hours ago

Open

Browse all tasks

Last updated on 23rd Aug 2026

Unlock new income opportunities in Sydney Northern Beaches

Explore light bar installation related jobs and discover your financial opportunities

Type of light bar installation job	1-2 tasks/week	3-5 tasks/week	5+ tasks/week
Mechanic	$450	$1,125	$1,575
Head Unit Installation	$430	$1,075	$1,505
Oil & Filter Change	$440	$1,100	$1,540

*Based on average light bar installation task prices in Sydney Northern Beaches. Actual marketplace earnings may vary

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

We've got you covered

Whether you’re a posting a task or completing a task, you can do both with the peace of mind that Airtasker is there to support.

Airtasker’s insurance cover