Find experienced local carpenters in QLD

Assemble 3m x 2.25m Gable Roof Shed on grass

We are looking fr someone to build us a bar out of timber - we will supply the specs for this (Dimensions are: 950mm wide x 950mm high x 600mm deep with a shelf in the middle at the back.) Supply of the materials and building of the bar. This can be done at our warehouse or brought to us fully made. We need to on or by 10th May.

Please fix burn from saucepan on laminate bench

Our kitchen counters are due to be replaced along with the cabinetry doors! We are hoping to replace the existing timber with new timber (or some other alternative if that works better, ie better for price and durability). The counters are priority, but we would also like the cabinet fronts changed! Ps apologies about the mess in the photos! A bit rushed! Thank you!

Supply and fit netting for a veggie patch box. Will need suitable staple gun to attach the netting. Box is around 3.5m wide, 1m deep and 1m tall.current netting was ripped out by a tradie to access under the box. This job also includes removal of current netting to leave a near job. Would like this to be done asap if possible. Unsure of what it will cost, so please provide your offer.

Measure, cut and installation of wood kitchen bench tops, “Merbau”. Measurements: approx. 720mm x 2600mm, with sink, single tap and glass top cut outs (no joints?).

* price is for labour only. Airtasker won’t allow me to put in full price so I’ll have to do labour only and then I can purchase the materials based on the list you provide and from your preferred suppliers if agreed. Supply and install solid oak flooring in chevron pattern (owner’s choice from the range available to you - please show examples when you quote) and all required materials to install to a high, streamlined, professional standard (please make allowance for some levelling - there is a slight bounce in 1-2 places and I want zero bounce, low noise etc). Includes subtle, professional finish to all doorways where it meets other materials (tiles) and around kitchen cabinetry/bench (to be agreed with owner but large chunky beads will not suffice) Remove skirting boards and remove current hybrid boards (stack for resale or you can take them and discount the value off the price) Replace with higher quality skirting boards when finished Remove and dispose of ALL rubbish Repair/make good any damage made to walls etc if occurs Downstairs will have all furniture removed and full access for 1-2 consecutive days. Upstairs the furniture will need to be moved from one half to the other and back again (can’t get all furniture downstairs) MUST BE PROFESSIONAL TIMBER FLOOR INSTALLER OR HAVE MANY YEARS EXPERIENCE LAYING TIMBER FLOORS BECAUSE YOU WILL NEED TO PROBLEM SOLVE ALL FINISHES WHERE MEETS OTHER MATERIALS ETC. Please include your experience when you quote. Photos of your work is even better!

Handyman required. Timber stair treads require adjustments. They some will need to be packed out with washes to bring them into alignment for compliance. About 4 hours work approximately. 12 stairs total. 10 may require adjustments by a few mm.

I need a qualified and experienced cabinet maker to finish few cabinets inside the van. My precious guy went to Cairns and left the job undone.

I am looking for some one to Remove old Kitchen dispose old kitchen Install new kitchen Price please Overall Job: 2280mm ] [ Floor Cabs: 910mm ] [ Wall Cabinets: 765mm ] <-Doors 765mm

Assemble flat pack ,,set up over the pool pump and drill in concrete bolts to hold shed down

Refinish veneer top of coffee table. Colour has faded but is a walnut finish

Looking for an experienced flatpack builder to build an executive desk. Needing someone with attention to detail, can do the job properly the first time and works relatively quickly. Please only offer if you can actually complete the task and will reply to messages.

need a retired, handyman to remove old broken cabinet and install a new one roughly measurements are 1200 wide 600 deep 900 high

Installation of 150mm feathered edge skirting with contact adhesive. Skirting and adhesive supplied. Room is 4900mmx4075mm. No need for cutting internal or external corners as skirting will sit flush when bent. There are 2 doors so skirting will need to be cut. Preferably this afternoon if possible.

Looking for an experienced flatpack builder with the necessary tools to build an executive desk. Needing someone with attention to detail, can do the job properly the first time and works relatively quick.

Need a Carpenter to help install a timber floor frame and sheeting over.

Build 2.25 x 1.5m garden and fasten to concrete slab. I have the fixings

I'd like to do some small renovations on my 3 bed apartment while living on-site. Kitchen, bathroom etc. I need some help from a qualified carpenter to discuss my options and then know the best place to start for planning and deciding on what's realistic within my budget.

We just had new flooring installed in our house and some of our doors did not have enough clearance for the height of the new floors, so we have had to take the doors off and need the bottoms trimmed back so that they fit again. Some doors seems to only need a few mm off and others could do with a couple cm trimmed. Looking for a carpenter to help us with this job, and future jobs too when we are ready for them, while we slowly fix up our older house to feel modern again! I added some pictures to show the bottom of the door and the height jump of new floor. We have four doors in total that need trimming. Two of them are our toilet and bathroom doors so earlier offers will be favoured! 😅