Find experienced local carpenters in Brisbane

Supply and fit netting for a veggie patch box. Will need suitable staple gun to attach the netting. Box is around 3.5m wide, 1m deep and 1m tall.current netting was ripped out by a tradie to access under the box. This job also includes removal of current netting to leave a near job. Would like this to be done asap if possible. Unsure of what it will cost, so please provide your offer.

* price is for labour only. Airtasker won’t allow me to put in full price so I’ll have to do labour only and then I can purchase the materials based on the list you provide and from your preferred suppliers if agreed. Supply and install solid oak flooring in chevron pattern (owner’s choice from the range available to you - please show examples when you quote) and all required materials to install to a high, streamlined, professional standard (please make allowance for some levelling - there is a slight bounce in 1-2 places and I want zero bounce, low noise etc). Includes subtle, professional finish to all doorways where it meets other materials (tiles) and around kitchen cabinetry/bench (to be agreed with owner but large chunky beads will not suffice) Remove skirting boards and remove current hybrid boards (stack for resale or you can take them and discount the value off the price) Replace with higher quality skirting boards when finished Remove and dispose of ALL rubbish Repair/make good any damage made to walls etc if occurs Downstairs will have all furniture removed and full access for 1-2 consecutive days. Upstairs the furniture will need to be moved from one half to the other and back again (can’t get all furniture downstairs) MUST BE PROFESSIONAL TIMBER FLOOR INSTALLER OR HAVE MANY YEARS EXPERIENCE LAYING TIMBER FLOORS BECAUSE YOU WILL NEED TO PROBLEM SOLVE ALL FINISHES WHERE MEETS OTHER MATERIALS ETC. Please include your experience when you quote. Photos of your work is even better!

Needing to replace rotten posts and facia boards under a deck to keep my pooch out from under the house. All timber and screws provided. 24/7 access.

Get this stain out of my carpet

Need quote to extend current concrete to make it bigger and longer

Seeking to install some plastic sheeting to cover a balcony structure, 3.3m Length by 1.2m Width. Job is to source sheets, bolt on to aluminium structure as per photos. Corrugations to face outwards away from balcony. Job to include acquiring the sheets in correct size.

Seeking a qualified cabinet maker to come on-site and design a new kitchen. Potentially a future opportunity to supply and install. Kitchen space is approximately 4.2m x 2.4m. Parking will be available in dedicated off-street parking

Changing a damaged wooden table and want to render it and make it have a concrete vibe. Ideally would be able to shape the corners into rounded edges with a jigsaw too

Installation of 150mm feathered edge skirting with contact adhesive. Skirting and adhesive supplied. Room is 4900mmx4075mm. No need for cutting internal or external corners as skirting will sit flush when bent. There are 2 doors so skirting will need to be cut. Preferably this afternoon if possible.

Sanding n restain decking

We are after someone who can give our verandah and deck a light sand and couple of coats of stain. Approx 32m2 over 2 areas. See pic for dimensions and back deck area. Don’t have photos of veranda

Install tv box in bar foyer in Brisbane city. Parking available. May need to scribe to floor. Assistance with cabinet available. Need to have have tools and experience

Red wine was spilt on the carpet. It’s an old stain. Most of the colour has been removed, it’s just a light stain that needs to be to go.

Remove current kitchen island and take away. Install new IKEA kitchen island to replace made up of 3 simple IKEA cabinets (see image). Then we need a smaller frame build attached to the right of the new island for a lower waterfall section to be covered in stone (by someone else). Looking for someone to start the job ASAP.

I have an unusable fully integrated half dishwasher. I'd like to replace it with my LG full size freestanding dishwasher under the bench. Task includes: - remove old fully integrated dishwasher - remove the drawer under - remove the side panels and bottom panel to create a space where it can fit my new freestanding dishwasher (60cm X 60cm X 85cm) under the kitchen bench. - place the dishwasher under the bench - install the dishwasher. The section of the cabinet is 60cm wide, so it should fit the dishwasher. Bonus if you can close the space between the kitchen bench and the top of the dishwasher. (Kitchen bench height 87cm vs dishwasher 85cm tall) ETA of dishwasher is tomorrow Monday 7/11. So anytime after that would be awesome!

Hi There We are hoping to find a long term installer for us to refer work to, starting with this project! - Details are below: Location: Clayfield Brisbane. Measurements: 1.81 m X 0.87 m 1.87 m X 0.87 m 1.87 m X 0.87 m 1.85 m X .087 m 0.90 m X 0.87 m 2.05 m X .087 m 2.13 m X 0.87 m Total panels: 14 (plastic green walls) The glass is enclosed in aluminium , and we would like to see the panels attached to the top metal frame and scrured with small screws along the top, side, and bottoms to cover the inserted grass - as our client wants to view the grass panels.

We recently had our oven replaced but the new oven is ever so slightly taller, which now means the cover panel above it won't fit flush again. The cover panel needs to be shaved down to allow it to sit flush again. Apartment is in Hamilton, flexible with day and time as work from home.

I have an old mirror to be taken down (presumably attached to tiles via liquid nails). mirror can be broken if required then, a new cabinet to be picked up from Newstead Bunnings, and installed to wall. wall to be attached to is tiles on gyprock. the lights and power point have been removed already

2-3 extra shelves needed in this utility cupboard to make the space more functional and practical

I replaced my ice machine and the new one was wider than expected, it is about 4mm too wide for the cabinet that is intended to house it. I need the cabinet modified to fit it... it *appears* as though there is a fillet panel between the carcases that can possibly be removed which would allow more than enough room, but... I'm not cabinet maker so, I don't know how to do this and don't want to just start tearing my cabinets apart. Hope you can help.