Find an experienced plumber in Port Melbourne

I have a leak coming from a hose either from the washing machine or condenser drier. I recently purchased a new drier and the leak has commenced after the instal. I have a feeling the hose just hasn’t been connected properly 🤷‍♀️ It’s now causing mould under the sink in the laundry so I need the leak fixed asap. - Due date: Needs to be done on Monday, 30 January 2023

Looking for a plumber to check out a loud ringing noise when toilet flushes at the same time as when shower or any other running water is on. I live in an apartment complex (not sure if that makes a difference pipe wise etc). - Due date: Flexible

Doing some updating of the house, and to replace kitchen faucet, tap in the bathroom, shower and bath, laundry sink. No work required on pipes etc, simple replacement. - Due date: Flexible

I have an apartment on level 4. There is a problem in the ensuite bathroom only When I turn on tap, it struggles to drain and bubbles come out of drain when I turn on shower tap, that too struggles to drain and bubbles come out fo drain Need it fixed asap - Due date: Needs to be done on Monday, 16 January 2023

Hi, I need a Spa Plumber to reconnect pipe in unit, the Spa has internal electric heater and pump. There’s easy access to pipes and spa - Due date: Flexible

Kitchen tap has become lose Need someone to tighten Hard for me to tighten from the bottom of sink without tools Should be easy with tools and if you have experience tightening taps - Due date: Needs to be done on Saturday, 7 January 2023

We have a leaking kitchen sink tap that leaks overnight when water pressure may be higher. It leaks from the top on the bench. May need a rubber gasket replaced.

Toilet blocked in Health Studio. Not sure if cause. Not flushing properly - Due date: Flexible

Install washing machine Existing pipework Existing pipes and drains Qualified plumber rewuiree Port melb location Flexible on day and time One job only

Licenced plumbing needed to relocate gas pipe for gas Cooktop in kitchen and taps to be relocated in the laundry. No labour work as all pipes are exposed no walls at the moment very easy job.Too hard to explain Here job is located in port melbourne if you can come in and price the job plz contact me.

Toilet makes hissing and refilling sound a long time after flushing. I think the cistern inlet valve needs replacing, however, the bit below (see photo) snapped off when I was removing it. Please quote for labour and acquiring parts only. I’ll reimburse parts on receipt value. - Due date: Flexible

I need old rough in switched to suit new tapware. (For the shower it stays in the same location) for the basin it needs to move to pick up new centre of vanity within 250mm. - shower tapware swap (new mixer supplied) new diverter supplied. - basin spindles no mixer needs to be switched and relocated to new centre of vanity. Along with outlet. Bathroom has been stripped so access no problem. - Due date: Flexible

Shower taps are very sensitive and require a lot of time to get temperature correct. We need this fixed please - Due date: Flexible

My two shower drains are blocked. I need someone to remove them and clean them. - Due date: Before Friday, 28 October 2022

Leaking tap in bathroom sink, may need a new washer. - Due date: Before Friday, 28 October 2022

Hello we need someone to come with a jet machine to unblock our main drain. We tried everything else (we have a drain cleaner machine but was not successful). Port Melbourne 3207

I need someone to replace my laundry tap, which is leaking into the cupboards below it. I'll supply the tap.

Water constantly running through toilet, have to ‘prop’ up the cistern float to stop water flow. Need a new dual flush cistern plus installation. - Due date: Flexible

The cistern flush system is broken and water flows non stop

In need of a handyman/woman to help with the following jobs: - re-align and tighten the kitchen tap - fix the dishwasher The dishwasher is currently displaying an error (see pictures). I'm by no means an expert, but according to the factory manual, it could be an issue with one of the sensors.