Find a fence installation professional in Bardon

Install three 1800 x 900mm Protector aluminium garden screens on one fence and two smaller 570 x570mm Matrix screens on another fence.

Restore existing chainwire fence to original position approx 10m section. . Will require some digging and resetting of posts. Build a new 5m section of chainwire fence. - Due date: Flexible

Hello, I am looking for someone to come and replace two fence posts that a sloping and place the fence back onto the post. I have the posts with me here-nil need to buy. I’m open to offers - Due date: Flexible

Looking for someone to supply and install a chain wire fence for a chicken run. Preferably woodland grey or black. 12m long x 1.2m high, with one gate for access. - Due date: Flexible

Build a timber fence between properties - approximately 20 metres - Due date: Flexible

Fence post is loose. It was pushed over in the flood. We don’t think it was dug deep enough when built, so may need a new post. The gate that is attached at the moment doesn’t shut properly, so that needs to be fixed at well - Due date: Flexible

Ideally I would like the existing fence removed too. It bolts together, and it has aluminum posts - which I think will pull out. Ideally I want the fence completed in a day or 2 days maximum because the neighbor has a dog The ground is almost flat - Due date: Flexible

Timber gates, double leaf, total length 2.4m. Swings outwards. I want the motors installed inside the gate, not outside. The width of car space is quite narrow, so I'd prefer if you can find a way to mount the motor inside the pillars with extendable arms, so they don't take up car space. Or install motors in the car width but they must be narrow profile. One side of the gate is bricks, the other side has a steel post, see pics. There is power supply on a horizontal beam, about 3m away. I am considering buying the below model, but if you have your own preferred models or refurbished motors on hand, I am open to recommendations. http://www.samtgatemotors.com.au/products-page/swing-gate-motors/came-stylo-double-swing-gate-motor-kit/ - Due date: Flexible

I have a 1.8m timber gate with all the hardware ready to go into an existing 1.8m fence. The current fence would need to have a section taken out to make room and using one existing post there would need to be another post concreted in for the other side as well.

I need 26.5m of fence (no gap between palings) including gate to be replaced as is on the slope. It also needs to be painted same colour as existing fence. Old timber to be removed from site. - Due date: Flexible

I need a 3.3m timber post installed - dig hole (min.600mm) insert post and concrete. Post and concrete supplied, Tools required for install to be supplied by airtasker. Post to be installed in ground shown in picture. Let me know if more info required. - Due date: Flexible

First quote: New timber dividing fence to be installed between residential properties in Bardon. Timber paling fence about 2meters in height with 2 timber sleepers on the bottom. Hardwood posts. About 34 meters in length. Nice flat land but there is a large tree that straddles both properties which needs to be accommodated. Second quote: Separately, I need a timber gate on steel frame to close off the left side of one house and a large gate to close off driveway on the other side.

We need to puppy proof our driveway - approximately 6-8 meters of picket fence plus a gate. Love to have this done by the end of this week!

From Friday the 20th to Sunday the 22nd I was looking to have a fence builder join me on building my 600mm retaining wall with approximately 20m of colonial fencing. I am looking for some one with more experience than me and to come with a cement mixer and the necessary tools required. I will pay $35 per hour cash for the work. I will be helping alongside to speed things up. Thanks

I require a silt fence to be installed on a residential building site. The site is 20m wide and the fence will need to match the the street frontage, the address is 20 Eastment St, Bardon.

Make an offer on an hourly rate. Probably a 2 person job. We need someone with fence building experience to help build a fence with hardwood posts and two hardwood rails horizontally. We then need solid rectangular mesh attached to the one side. Keen to get it done starting anything from tomorrow. Access to a hole/core digger foe the post holes would be a benefit too but not essential.

Need a qualified person to: 1. Dig out and remove a timber post and its concrete base; 2. Dig that hole further to 60cm and install a steel post with postcrete. 3. Dig second hole to 60cm depth and install a steel post with postcrete. We provide the two Steel posts - galvanised steel 75mm x 75mm 2.4 m long each. We have 4 x bags of quickset post mix cement. Please provide quote!

Hi - looking for someone to supply and install approx 16m of silt fence in Bardon. 1 x 10m run along the back fence & 1 x 6m run in the middle of the property. Works can be done at anytime.

Note: the $10 job price is arbitrary- feel free to quote. We want to build a small fence in our yard. See pics. The fence comes out about 600m from the garden border and then in a straight line to just past the black stair hand rail. I will also see if I can post a video explaining too. We can purchase the supplies or you can, so please quote the materials separately in a comment. I’ll put an arbitrary $10 as the job so you can quote. Cheers

Hi there Looking for someone to build a simple dog fence (w small gate). Basically just one horizontal line - At a property in Bardon, Brisbane. I'm happy to provide materials (Bunnings etc) but if you have them - I'll pay you for these. Ideally one simple line of fencing with joins to the existing fence: ~10m (length) & 150cm (or higher) in height. n.b approx dimensions for now- with a gate for an entrance. I have in mind the aluminium black pool fence lines from bunnings which can come with a gate. Job available between Saturday 3rd Oct - the following Saturday. I'm available & willing to help carry, install, help out.