Find experienced local carpenters in North Sydney

Repair timber table top, refer to photos before, can send more. Part of the top that holds the timber planks in place has come loose.

Please come to provide a quote to repair and replace the damaged deck. Doesn’t have to be completely new look again, only replace the bit that is necessary. Because I will demolish the deck in a couple of years. Experienced and licensed carpenter only. Thanks Ronnie

Need a cabinet to be made , to cover hot water tank

Some deck wold and a few bits of an old shelf together with a few bits of support timber to be removed. We have easy access and easy parking so should be a simple job. See photos.

Small amount of rot in bottom corner of railing requires repair. Need to replace the bottom railing. Both sides of the corner as pictured.

I'm looking for someone with carpentry experience to custom make an outdoor timber aircon cover that can fit wires on one side. The measurement will be 1200mm length x 600mm depth x 900mm height. Examples of the cover is attached

Hi, Please check the attachment. It includes all measurements instructions and material to builds a closet.

I have had a pool roller and cover delivered, but it needs installing. The roller has a few pieces to put together - I have the instructions for that. The cover needs to be cut to size once it’s been installed. I could possibly do that myself, but if an experienced person could do that as well, it would be my preference

Some kitchen and living room doors need hinges to be adjusted. Additionally, one of the bedroom doors doesn't close properly and needs some adjustments.

Sand back cedar gates Re stain gates Repair and replace a piece of treated pine battern on the gate and repaint

It’s a a 2.25m wide x 0.78m deep x 1.31m bike shed that needs installation in my garden on concrete fixing. I can give you hand if need to. It’s new bought from EasyShed.

Fix/or replace two pieces of broken wood and paint them, very simple job Please include supply and install in this job, price should include all fees and charges Top piece 2600mm x 140mm x 50mm Mid piece 1890mm x 25mm x 90mm

Replace a rotted timber of deck

The area is 8m2. I’ve ordered width: 288cm height: 270cm then trimmed on site. Here is a link: https://oliveetoriel.com/products/trellis-luxe-in-heritage-blue-wallpaper Price negotiable. Please give a quote.

Hi carpenters or handymen! I’m needing someone that can install wood trim and caulk to my laundry bench to make it look pretty ! Will also need the person to maybe tidy up the cut out and seal it too :) Will pay extra for materials :) Please reach out if you can help !

Secure balcony railing/replace damaged slats Fix kitchen door Shave off linen cupboard door Lattice (maybe) to hide ugly pipes Lattice (maybe) to cover underhouse area replace 1 metre of vinyl in kitchen Must have great airtasker references Not sure how long this will take so have put up hourly rate and pay cash for rest

As the photos show, there is a collection of about 20 kitchen knives that need sharpening. Three more are in dishwasher. Make an offer - I have no idea what the job is worth. - Due date: Flexible

I installed a eket cabinet (details in picture)into the drywall. However was unable to successfully install one of the wall brackets and is now uneven. Need help even it out. Also I have a table I would like to custom cut for it to be at the top of the cabinet (1770x360). Any further questions please ask. It is a drywall and studs.

I need to relocate my backyard sheshed to ensure a 90cm clearance from my fence on all sides. Currently, the gap is about 30cm. The shed is a 3m x 3m treated timber cabin kit from https://www.sheshedz.com.au/. It's built on ground bearers and has shingle roofing. The floor timbers have been partially dismantled (as shown in the photos). If disassembling the roof timbers requires removing the shingles, you don't need to reinstall the shingles but need to reassemble all timbers and the window and the door. The job includes preparing the new foundation and moving the shed, and ensuring there are no hidden costs. You're welcome to inspect the shed beforehand if needed.

I want a metal shed to be assembled and installed on a concrete slab, using concrete fixings. The shed is Easyshed: 1.5m x 0.78m x 2.12m tall. Date to be decided, once I am informed by company of delivery date. Approx date should be late March. - Due date: Flexible