Find experienced local carpenters in Glenelg

Would like a very basic wardrobe built please. 1.16m wide x 36cm deep x 2m tall (height can be Approx). Would like a few drawers, then 1-2 hanging depending on space. Similar to below image and have also attached image of the space. - Due date: Before Tuesday, 16 January 2024

Installation required for a 3m x 3.6m x 2.7m (Height) gazebo from Bunnings. I need someone whom understands waterproofing and has a builders/contractors license. The gazebo will be located in my courtyard, the 4 posts needs to be securely bolted onto the ground (see image of red brick pavement), or concreted in. I can be available to assist with the installation. Thanks - Due date: Before Saturday, 30 December 2023

I need a professional cabinet market whom understands how to measure kitchen/laundry doors, hinges, draws, kicker and panels properly, as I need to place a custom order. All that needs to be measured is in the photos. Thanks - Due date: Before Thursday, 30 November 2023

I need a partial kitchen install; doors installed below benchtop, cupboards installed at eye height, kickboards & sink cutout. - Due date: Needs to be done on Friday, 27 October 2023

Two identical under sink cabinet doors (730x480mm) need to be reduced in width by approx 90 mm each. Anyone out there with the tools and skills to achieve this? It’s not going in the queens kitchen, but we’d love the adjustment to look as seamless as possible. We are thinking, a couple of clean cuts down the middle, and then some carpentry magic to get it back to strength. Perhaps some doweling/gluing/reinforcement on the back?? Please let me know how you’re thinking to go about it, and we will get back to you asap. Happy to drop it to you. Cheers, Andrew - Due date: Flexible

Need a wooden base with at least one drawer built in between 2 walls. Space slightly shorter than conventional single bed but fits mattress,(188cm to skirting board) will be used as day bed. The space with mattress on floor is shown below. The width of the space to the skirting board is 188cm, most single bed frames are around 200cm. The mattress would need to sit on the top, not be enclosed. Have also added photos of preferred look. Could potentially cut base of be around skirting board to get to 190cm. - Due date: Flexible

erect new Stratco garden shed on new concrete base. Handy Highlander shed 3.5 x 2.6m approx. - Due date: Flexible

We need a kitchen bench removed and a new one installed. I’ve provided photos to give an idea of what is there now. The green top in other words has to be removed. We want a “Bunnings” laminated timber bench top. We can give you the style etc to you so you can then quote including the material. We are prepared to pay for the measure up and qte, as we would have to do if Bunnings would measure snd qte bench top. (They only measure and qte full kitchen…..not just if it’s the bench top) If it helped we could pick up the materials after you give full measure and qte on installation. - Due date: Flexible

Please ignore the budget. We have no idea what it will cost so I have put in $10 just to register the job. Obviously this is not the price!!! We have the same door as the website following but ours is cream. The powder coating is coming off and it is a bit worn in areas. https://www.bunnings.com.au/custom-barrier-door-harrington-sp14ab_p2029987 We would be happy with a repaint. - Due date: Flexible

Cabinet maker needed to build a carcass for a bar. - Due date: Needs to be done on Thursday, 15 December 2022

New shed (narrow wall mounted apartment patio shed .80 x 3.7m) ready to go. Glenelg

Remove shelving in pantry and a section of walk in robe to access for removal of old unit and install of new air conditioner. Units to be saved to be re installed at a later date. - Due date: Before Thursday, 1 December 2022

I need a wall built to enclose part of a loungeroom (to create an extra bedroom) - Due date: Flexible

Would you have the expertise and capacity to paint our blackwood kitchen cabinets? We are redesigning our kitchen and reusing our current kitchen cabinets and buying a few more second hand ones from Gumtree. However, we've now exposed our wooden floorboards, so aiming to change the cabinets from wood to an off-white colour. There are 27 kicthen cabinet doors that need painting both sides. - Due date: Flexible

Shed Builder. Half built shed just needs finishing off. - Due date: Flexible

Need some non pre-glued 1mm edge-banding applied to two pre cut cabinet doors. I have the doors cut and the matching edge-banding. Just need a cabinetmaker to apply and trim it. Cheers Sam

Looking for an experienced Carpenter/Joiner to prep and install our three branded wall concepts in an existing retail space. Ideally work would commence Early October 2021 - estimated prep and install time is 3-4 days. You can find detailed build notes attached, but here is a brief scope:    * Check measure site against design build notes (attached).   * Prep (cut to size and paint) mdf vgroove panelling and pine trim for Earth Nymph concept.   * Fit Earth Nymph (white) Display Wall system, pre painted panels and trim to wall, fill and touch up where necessary.   * Fit prefabricated Pacific Creations Display Wall system to wall, fill and touch up where necessary.   * Clad Kooringal wall section with textured panelling, fill and paint.   * Assemble and install Kooringal Wall Shelving and Mirror.   * Install Brand Signage above each concept (as advised by TSD)   * Clean site and dispose of all rubbish.   If interested, please get in touch to arrange a time to go through the project in more detail.

I am looking at having a basic roof/shelter built, outside in my patio. It currently has a structure with mesh, (that can be used for measurements and design) but the wood requires replacing. I am hoping for a colorbond material or something similar. I would like someone that can provide all tooling and labour. Building experience or trade would be favoured. If interested please provide quote and an estimated time this can be completed.

The washing machine alcove in our rental is too small. We need someone to build a bench/table that doesn’t need to be drilled/secured to any walls. There is an exisiting cabinet the bench could rest on one side with an upside down “L” shape supporting the other side. Doesn’t need to be fancy, just needs to hold the machine. Alcove space Width - 57cm Depth - 57cm Height - 88cm

Build a timber plinth for bath to go on 2000x1200x150mm.. finish with similar boards to bedroom